LM2575T-12/NOPB National Semiconductor, LM2575T-12/NOPB Datasheet - Page 23
![IC REG SIMPLE SWITCHER TO-220-5](/photos/7/60/76069/pkg_t05a_drawing__14_sml.jpg)
LM2575T-12/NOPB
Manufacturer Part Number
LM2575T-12/NOPB
Description
IC REG SIMPLE SWITCHER TO-220-5
Manufacturer
National Semiconductor
Series
SIMPLE SWITCHER®r
Type
Step-Down (Buck)r
Datasheet
1.LM2575S-5.0NOPB.pdf
(28 pages)
Specifications of LM2575T-12/NOPB
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
12V
Current - Output
1A
Frequency - Switching
52kHz
Voltage - Input
4 ~ 40 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-220-5 (Straight Leads)
Primary Input Voltage
25V
No. Of Outputs
1
Output Voltage
5V
Output Current
1A
No. Of Pins
5
Operating Temperature Range
-40°C To +125°C
Msl
MSL 1 - Unlimited
Filter Terminals
Through Hole
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
Other names
*LM2575T-12
*LM2575T-12/NOPB
LM2575T-12
*LM2575T-12/NOPB
LM2575T-12
Definition of Terms
BUCK REGULATOR
A switching regulator topology in which a higher voltage is
converted to a lower voltage. Also known as a step-down
switching regulator.
BUCK-BOOST REGULATOR
A switching regulator topology in which a positive voltage is
converted to a negative voltage without a transformer.
DUTY CYCLE (D)
Ratio of the output switch's on-time to the oscillator period.
CATCH DIODE OR CURRENT STEERING DIODE
The diode which provides a return path for the load current
when the LM2575 switch is OFF.
EFFICIENCY (η)
The proportion of input power actually delivered to the load.
CAPACITOR EQUIVALENT SERIES RESISTANCE (ESR)
The purely resistive component of a real capacitor's
impedance (see Figure 16). It causes power loss resulting in
capacitor heating, which directly affects the capacitor's oper-
ating lifetime. When used as a switching regulator output filter,
higher ESR values result in higher output ripple voltages.
Most standard aluminum electrolytic capacitors in the
100 μF–1000 μF range have 0.5Ω to 0.1Ω ESR. Higher-grade
capacitors (“low-ESR”, “high-frequency”, or “low-induc-
tance”') in the 100 μF–1000 μF range generally have ESR of
less than 0.15Ω.
FIGURE 16. Simple Model of a Real Capacitor
1147521
23
EQUIVALENT SERIES INDUCTANCE (ESL)
The pure inductance component of a capacitor (see Figure
16). The amount of inductance is determined to a large extent
on the capacitor's construction. In a buck regulator, this un-
wanted inductance causes voltage spikes to appear on the
output.
OUTPUT RIPPLE VOLTAGE
The AC component of the switching regulator's output volt-
age. It is usually dominated by the output capacitor's ESR
multiplied by the inductor's ripple current (ΔI
to-peak value of this sawtooth ripple current can be deter-
mined by reading the Inductor Ripple Current section of the
Application hints.
CAPACITOR RIPPLE CURRENT
RMS value of the maximum allowable alternating current at
which a capacitor can be operated continuously at a specified
temperature.
STANDBY QUIESCENT CURRENT (I
Supply current required by the LM2575 when in the standby
mode (ON /OFF pin is driven to TTL-high voltage, thus turning
the output switch OFF).
INDUCTOR RIPPLE CURRENT (ΔI
The peak-to-peak value of the inductor current waveform,
typically a sawtooth waveform when the regulator is operating
in the continuous mode (vs. discontinuous mode).
CONTINUOUS/DISCONTINUOUS MODE OPERATION
Relates to the inductor current. In the continuous mode, the
inductor current is always flowing and never drops to zero, vs.
the discontinuous mode, where the inductor current drops to
zero for a period of time in the normal switching cycle.
INDUCTOR SATURATION
The condition which exists when an inductor cannot hold any
more magnetic flux. When an inductor saturates, the inductor
appears less inductive and the resistive component domi-
nates. Inductor current is then limited only by the DC resis-
tance of the wire and the available source current.
OPERATING VOLT MICROSECOND CONSTANT (E•T
The product (in VoIt•μs) of the voltage applied to the inductor
and the time the voltage is applied. This E•T
measure of the energy handling capability of an inductor and
is dependent upon the type of core, the core area, the number
of turns, and the duty cycle.
IND
STBY
)
)
op
IND
constant is a
). The peak-
www.national.com
op
)