LM2576T-15/NOPB National Semiconductor, LM2576T-15/NOPB Datasheet - Page 14
![IC REG SIMPLE SWITCHER TO-220-5](/photos/7/60/76069/pkg_t05a_drawing__14_sml.jpg)
LM2576T-15/NOPB
Manufacturer Part Number
LM2576T-15/NOPB
Description
IC REG SIMPLE SWITCHER TO-220-5
Manufacturer
National Semiconductor
Series
SIMPLE SWITCHER®r
Type
Step-Down (Buck)r
Datasheet
1.LM2576T-5.0NOPB.pdf
(24 pages)
Specifications of LM2576T-15/NOPB
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
15V
Current - Output
3A
Frequency - Switching
52kHz
Voltage - Input
4 ~ 40 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-220-5 (Straight Leads)
Input Voltage
40V
Output Current
3A
Output Voltage
15V
No. Of Pins
5
Operating Temperature Range
-40°C To +125°C
Msl
MSL 1 - Unlimited
Switching Frequency Max
52kHz
Filter Terminals
Through Hole
Rohs Compliant
Yes
Input Voltage Primary Max
40V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Other names
*LM2576T-15
*LM2576T-15/NOPB
LM2576T-15
*LM2576T-15/NOPB
LM2576T-15
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LM2576T-15/NOPB
Manufacturer:
TI/德州仪器
Quantity:
20 000
www.national.com
LM2576 Series Buck Regulator Design Procedure
To further simplify the buck regulator design procedure, Na-
tional Semiconductor is making available computer design
software to be used with the SIMPLE SWITCHER line of
2. Inductor Selection (L1) A. Calculate the inductor Volt
following formula:
match it with the E • T number on the vertical axis of the
Inductor Value Selection Guide shown in Figure 7. C. On
the horizontal axis, select the maximum load current. D.
Identify the inductance region intersected by the E • T
value and the maximum load current value, and note the
inductor code for that region. E. Identify the inductor value
from the inductor code, and select an appropriate inductor
from the table shown in Figure 9. Part numbers are listed
for three inductor manufacturers. The inductor chosen
must be rated for operation at the LM2576 switching fre-
quency (52 kHz) and for a current rating of 1.15 x I
For additional inductor information, see the inductor sec-
tion in the application hints section of this data sheet.
3. Output Capacitor Selection (C
the output capacitor together with the inductor defines
the dominate pole-pair of the switching regulator loop.
For stable operation, the capacitor must satisfy the
following requirement:
and 2200 µF that will satisfy the loop requirements for
stable operation. But to achieve an acceptable output
ripple voltage, (approximately 1% of the output voltage)
and transient response, the output capacitor may need to
be several times larger than the above formula yields. B.
The capacitor’s voltage rating should be at last 1.5 times
greater than the output voltage. For a 10V regulator, a
rating of at least 15V or more is recommended. Higher
voltage electrolytic capacitors generally have lower ESR
numbers, and for this reason it may be necessary to select
a capacitor rate for a higher voltage than would normally be
needed.
4. Catch Diode Selection (D1) A. The catch-diode
current rating must be at least 1.2 times greater than the
maximum load current. Also, if the power supply design
must withstand a continuous output short, the diode
should have a current rating equal to the maximum
current limit of the LM2576. The most stressful condition
for this diode is an overload or shorted output. See diode
selection guide in Figure 8. B. The reverse voltage rating
of the diode should be at least 1.25 times the maximum
input voltage.
5. Input Capacitor (C
electrolytic bypass capacitor located close to the
regulator is needed for stable operation.
• microsecond constant, E • T (V • µs), from the
The above formula yields capacitor values between 10 µF
PROCEDURE (Adjustable Output Voltage Versions)
B. Use the E • T value from the previous formula and
IN
) An aluminum or tantalum
OUT
) A. The value of
LOAD
.
14
switching regulators. Switchers Made Simple (Version 3.3)
is available on a (3
ers from a National Semiconductor sales office in your area.
2. Inductor Selection (L1) A. Calculate E • T (V • µs)
Region = H150 E. Inductor Value = 150 µH Choose from
AIE part #415-0936 Pulse Engineering part #PE-531115,
or Renco part #RL2445.
3. Output Capacitor Selection (C
≥ 680 µF C
4. Catch Diode Selection (D1) A. For this example, a
3.3A current rating is adequate. B. Use a 30V 31DQ03
Schottky diode, or any of the suggested fast-recovery
diodes in Figure 8.
5. Input Capacitor (C
capacitor located near the input and ground pins
provides sufficient bypassing.
However, for acceptable output ripple voltage select C
B. E • T = 115 V • µs C. I
EXAMPLE (Adjustable Output Voltage Versions)
OUT
= 680 µF electrolytic capacitor
(Continued)
1
⁄
2
") diskette for IBM compatible comput-
IN
) A 100 µF aluminum electrolytic
LOAD
(Max) = 3A D. Inductance
OUT
)
OUT