LT1054CS8#PBF Linear Technology, LT1054CS8#PBF Datasheet - Page 3

• Manufacturer Part Number: LT1054CS8#PBF
• Description: IC VOLT CONV SW-CAP W/REG 8SOIC
• Manufacturer: Linear Technology
• Type: Switched Capacitor (Charge Pump), Doubler, Invertingr

Specifications of LT1054CS8#PBF

• Internal Switch(s): Yes
• Synchronous Rectifier: No
• Number Of Outputs: 1
• Voltage - Output: Adjustable
• Current - Output: 100mA
• Frequency - Switching: 25kHz
• Voltage - Input: 3.5 ~ 15 V
• Operating Temperature: 0°C ~ 100°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Primary Input Voltage: 15V
• No. Of Outputs: 1
• Output Current: 100mA
• No. Of Pins: 8
• Operating Temperature Range: 0°C To +100°C
• Msl: MSL 1 - Unlimited
• Switching Frequency Max: 40kHz
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -

ELECTRICAL CHARACTERISTICS
temperature range, otherwise specifications are at T
PARAMETER
Supply Current
Supply Voltage Range
Voltage Loss (V
Output Resistance
Oscillator Frequency
Reference Voltage
Regulated Voltage
Line Regulation
Load Regulation
Maximum Switch Current
Supply Current in Shutdown
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The absolute maximum supply voltage rating of 16V is for
unregulated circuits using LT1054. For regulation mode circuits using
LT1054 with V
increased to 20V. The absolute maximum supply voltage for LT1054L is 7V.
Note 3: The devices are guaranteed by design to be functional up to the
absolute maximum junction temperature.
Note 4: For voltage loss tests, the device is connected as a voltage inverter,
with pins 1, 6, and 7 (3, 12, and 13 S package) unconnected. The voltage
losses may be higher in other configurations.
OUT
IN
– |V
≤ 15V at Pin 5 (Pin 11 on S package), this rating may be
OUT
|)
CONDITIONS
I
LT1054
LT1054L
C
∆I
LT1054: 3.5V ≤ V
LT1054L: 3.5V ≤ V
I
V
LT1054: 7V ≤ V
V
V
I
I
I
LOAD
REF
OUT
OUT
OUT
IN
IN
IN
PIN1
OUT
= C
= 7V, T
= 7V, 100Ω ≤ 500Ω (Note 6)
= 60µA, T
= 10mA
= 100mA
= 125mA (LT1054L)
= 0mA
= 0V
= 10mA to 100mA (Note 5)
OUT
A
= 25°C. (Note 7)
J
= 100µF Tantalum (Note 4)
= 25°C, R
J
IN
The
= 25°C
≤ 12V, R
IN
IN
l
≤ 15V
≤ 7V
L
denotes the specifications which apply over the full operating
LT1054:
LT1054L: V
= 500Ω (Note 6)
L
= 500Ω (Note 6)
Note 5: Output resistance is defined as the slope of the curve, (∆V
∆I
portion of the curve. The incremental slope of the curve will be higher at
currents <10mA due to the characteristics of the switch transistors.
Note 6: All regulation specifications are for a device connected as a
positive-to-negative converter/regulator with R1 = 20k, R2 = 102.5k,
C1 = 0.002µF , (C1 = 0.05µF S package) C
tantalum.
Note 7: The S8 package uses a different die than the H, J8, N8 and S
packages. The S8 device will meet all the existing data sheet parameters.
See Regulation and Capacitor Selection in the Applications Information
section for differences in application requirements.
OUT
), for output currents of 10mA to 100mA. This represents the linear
V
V
V
IN
IN
IN
IN
= 3.5V
= 15V
= 3.5V
= 7V
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
LT1054/LT1054L
–4.70
MIN
2.35
2.25
3.5
3.5
15
15
IN
= 10µF tantalum, C
–5.00
0.35
1.10
1.35
2.50
TYP
300
100
2.5
3.0
2.5
3.0
10
25
25
10
5
–5.20
MAX
0.55
1.60
1.75
2.65
2.75
200
4.0
5.0
4.0
5.0
15
15
40
35
25
50
7
OUT
OUT
= 100µF
UNITS
1954lff
3
vs
kHz
kHz
mA
mA
mA
mA
mV
mV
mA
µA
Ω
V
V
V
V
V
V
V
V