MAX845ESA+T Maxim Integrated Products, MAX845ESA+T Datasheet - Page 13
![IC DRVR TRANSF ISO 8-SOIC](/photos/1/39/13902/8-soic_21-0042b_sml.jpg)
MAX845ESA+T
Manufacturer Part Number
MAX845ESA+T
Description
IC DRVR TRANSF ISO 8-SOIC
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX845ESA.pdf
(16 pages)
Specifications of MAX845ESA+T
Applications
Transformer Driver, PCMCIA
Voltage - Input
3.3V, 5V
Number Of Outputs
1
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Supply Voltage (max)
5 V
Supply Voltage (min)
3.3 V
Supply Current
1.1 mA
Maximum Power Dissipation
471 mW
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Supply Voltage
5V
Digital Ic Case Style
SOIC
No. Of Pins
8
No. Of Regulated Outputs
2
Operating Temperature Range
-40°C To +85°C
Supply Voltage Range
2.5V To 6V
Termination Type
SMD
Rohs Compliant
Yes
Filter Terminals
SMD
Leaded Process Compatible
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
2) Use a test winding to measure ET product (if using
3) Determine the number of turns required for the pri-
4) Select a rectifier topology based on performance
5) Work backward from V
6) Wind the transformer with the largest diameter wire
Bobbin or drum cores suffer from low coupling between
windings. This usually requires bifilar winding for the
two halves of the primary.
Due to the inherent complexity of magnetic circuit
design, it will be necessary to build a prototype and re-
iterate the design. If necessary, adjust the design by
altering the number of primary or secondary turns, or the
wire gauge. If using a different core material or geome-
try, evaluate its ET product or A
Figure 11 shows various rectifier topologies. Refer to
Table 2 for selection criteria. The turns ratio of the trans-
former must be set to provide the minimum required out-
put voltage at the maximum anticipated load, with the
minimum expected input voltage. In addition, the calcu-
lations should allow for worst-case losses in the recti-
fiers. Since the turns ratio determined in this manner will
ordinarily produce a much higher voltage at the sec-
ondary under conditions of high input voltage and/or
light loading, be careful to prevent an overvoltage con-
dition from occurring (see the Output Voltage vs. Load
Current graph in the Typical Operating Characteristics ).
an ungapped toroid) and/or A
mary winding. For an ungapped toroid, ET product
from center-tap to D1 must be at least 5V-µs. Other
core types must have sufficient inductance to limit
D1 and D2 output current under minimum load con-
ditions, and must not be allowed to saturate.
requirements (ripple vs. loss, and space required
for secondary winding). Refer to Table 2, Rectifier
Topology Trade-Offs.
mine the secondary to primary turns ratio. Include
losses in the rectifier diodes, and estimate resistive
losses in the windings. For load currents exceed-
ing 150mA, use a voltage step-down transformer to
step up the output current from the MAX845. Do
not exceed the MAX845’s absolute maximum out-
put current rating (200mA).
that will fit the winding area. Select a wire gauge to
fill the winding aperture as much as possible.
Larger diameter wire has lower resistance per unit
length. Doubling the wire diameter reduces resis-
tive losses by a factor of four.
______________________________________________________________________________________
OUT
L
Rectifier Topology
as described above.
requirements to deter-
L
value for the core.
Isolated Transformer Driver
for PCMCIA Applications
Use fast-switching diode rectifiers. Ordinary silicon sig-
nal diodes like the 1N914 or 1N4148 may be used for
low output current levels (less than 50mA), but Schottky
diodes have a lower forward voltage drop and should
be used for higher-current applications. Central
Semiconductor has low-current Schottky diodes as
duals in SOT-23 packages (CMPSH-3 series). The
Nihon SB05W05C is a common-cathode dual in a SOT-
23; it works well in the two-diode full-wave configura-
tion. The Motorola MBR0520 is an excellent choice for
all configurations.
Figure 11a. 2-Diode Push-Pull
Figure 11b. 4-Diode Bridge
Figure 11c. Voltage Doubler
V
IN
V
V
IN
IN
GND1 GND2
2
GND1 GND2
MAX845
GND1 GND2
2
2
MAX845
MAX845
V
CC
V
V
6
CC
CC
7
6
6
7
7
D1
D2
D1
D2
D1
D2
1
8
1
8
1
8
Diodes
13