EL5225IRZ Intersil, EL5225IRZ Datasheet - Page 5
![IC VOLT GEN 10CH TFT-LCD 24TSSOP](/photos/6/65/66570/20-24-tssop_sml.jpg)
EL5225IRZ
Manufacturer Part Number
EL5225IRZ
Description
IC VOLT GEN 10CH TFT-LCD 24TSSOP
Manufacturer
Intersil
Datasheet
1.EL5225IRZ-T13.pdf
(12 pages)
Specifications of EL5225IRZ
Applications
Converter, TFT, LCD
Voltage - Input
5 ~ 16.5 V
Number Of Outputs
10
Voltage - Output
0.5 ~ 14.95 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
24-TSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EL5225IRZ
Manufacturer:
ELAMTEC
Quantity:
1 867
Part Number:
EL5225IRZ
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
EL5225IRZ-T7
Manufacturer:
INTERSIL
Quantity:
20 000
Typical Performance Curves
General Description
The EL5225 provides a versatile method of providing the
reference voltages that are used in setting the transfer
characteristics of LCD display panels. The V/T
(Voltage/Transmission) curve of the LCD panel requires that
a correction is applied to make it linear; however, if the panel
is to be used in more than one application, the final curve
may differ for different applications. By using the EL5225,
the V/T curve can be changed to optimize its characteristics
according to the required application of the display product.
Each of the eight reference voltage outputs can be set with a
10-bit resolution. These outputs can be driven to within
50mV of the power rails of the EL5225. As all of the output
buffers are identical, it is also possible to use the EL5225 for
applications other than LCDs where multiple voltage
references are required that can be set to 10 bit accuracy.
FIGURE 7. SMALL SIGNAL RESPONSE (RISING FROM 0V
FIGURE 9. POWER DISSIPATION vs AMBIENT
200mV
5V
0V
5V
0V
0V
1.4
1.2
0.8
0.6
0.4
0.2
1
0
0
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
1.176W
TO 200mV)
TEMPERATURE
25
AMBIENT TEMPERATURE (°C)
OUTPUT
M=400µs/DIV
50
5
75
85
(Continued)
SCLK
SDA
100
125
EL5225
Digital Interface
The EL5225 uses a simple 3-wire SPI compliant digital
interface to program the outputs. The EL5225 can support
the clock rate up to 5MHz.
Serial Interface
The EL5225 is programmed through a three-wire serial
interface. The start and stop conditions are defined by the
ENA signal. While the ENA is low, the data on the SDI (serial
data input) pin is shifted into the 16-bit shift register on the
positive edge of the SCLK (serial clock) signal. The MSB (bit
15) is loaded first and the LSB (bit 0) is loaded last (see
Table 1). After the full 16-bit data has been loaded, the ENA
is pulled high and the addressed output channel is updated.
The SCLK is disabled internally when the ENA is high. The
SCLK must be low before the ENA is pulled low.
FIGURE 10. POWER DISSIPATION vs AMBIENT
FIGURE 8. SMALL SIGNAL RESPONSE (FALLING FROM
200mV
5V
0V
5V
0V
0V
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0
JEDEC JESD51-3 LOW EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
781mW
200mV TO 0V)
TEMPERATURE
OUTPUT
25
AMBIENT TEMPERATURE (°C)
50
M=400µs/DIV
75
85
SCLK
100
SDA
March 11, 2004
125
FN7356.0