ISL6266AIRZ Intersil, ISL6266AIRZ Datasheet - Page 22
![IC CORE CTRLR 2PHASE 48-QFN](/photos/18/29/182944/48-vqfn_l48_sml.jpg)
ISL6266AIRZ
Manufacturer Part Number
ISL6266AIRZ
Description
IC CORE CTRLR 2PHASE 48-QFN
Manufacturer
Intersil
Datasheet
1.ISL6266HRZ.pdf
(30 pages)
Specifications of ISL6266AIRZ
Applications
Converter, Intel IMVP-6
Voltage - Input
5 ~ 25 V
Number Of Outputs
1
Voltage - Output
0.3 ~ 1.5 V
Operating Temperature
-40°C ~ 100°C
Mounting Type
Surface Mount
Package / Case
48-VQFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL6266AIRZ
Manufacturer:
Intersil
Quantity:
166
volt-second balance. The ISL6266 continues to turn on the
lower MOSFET for the inactive channel to deplete the induced
field with minimum power loss.
Component Selection and Application
Soft-Start and Mode Change Slew Rates
The ISL6266A uses two slew rates for various modes of
operation. The first is a slow slew rate used to reduce in-rush
current during start-up. It is also used to reduce audible noise
when entering or exiting Deeper Sleep Mode. A faster slew rate
is used to exit out of Deeper Sleep and to enhance system
performance by achieving active mode regulation more quickly.
Note that the SOFT capacitor current is bidirectional. The
current is flowing into the SOFT capacitor when the output
voltage is commanded to rise and out of the SOFT capacitor
when the output voltage is commanded to fall.
Figure 36 illustrates how the two slew rates are determined
by commanding one of two current sources into or out of the
SOFT pin. The capacitor from the SOFT pin to ground holds
the voltage commanded by the two current sources. The
voltage is fed into the non-inverting input of the error
amplifier and sets the regulated system voltage. Depending
on the state of the system (Start-Up or Active mode) and the
state of the DPRSLPVR pin, one of the two currents shown
in Figure 36 will be used to charge or discharge this
capacitor, thereby controlling the slew rate of the newly
commanded voltage. These currents can be found under
“SOFT-START CURRENT” on page 4 of the “Electrical
Specifications” table.
The first current, labeled I
Specifications” table on page 4 as 42µA. This current is used
during soft-start. The second current (I
get the larger of the two currents, labeled I
“Electrical Specifications” table on page 4. This total current
is typically 205µA with a minimum of 180µA.
FIGURE 36. SOFT PIN CURRENT SOURCES FOR FAST AND
C
SOFT
SLOW SLEW RATES
+
SOFT
V
REF
I
SS
SS
, is given in the “Electrical
22
ISL6266, ISL6266A
I
2
AMPLIFIER
+
2
ERROR
) sums with I
GV
in the
ISL6266, ISL6266A
SS
to
The IMVP-6+ specification dictates the critical timing
associated with regulating the output voltage. The symbol,
SLEWRATE, as given in the IMVP-6+ specification will
determine the choice of the SOFT capacitor (C
Equation 4.
Using a SLEWRATE of 10mV/µs and the typical I
given in the “Electrical Specifications” table on page 4 of
205µA, C
A choice of 0.015µF would guarantee a SLEWRATE of
10mV/µs is met for the minimum I
“Electrical Specifications” table on page 4. This choice of
C
should expect the output voltage to slew to the boot value of
1.2V at a rate given by Equation 6.
Selecting RBIAS
To properly bias the ISL6266A, a reference current is
established by placing a 147kΩ, 1% tolerance resistor from
the RBIAS pin to ground. This will provide a highly accurate
10µA current source from which the OCSET reference
current can be derived.
Care should be taken in layout that the resistor is placed
very close to the RBIAS pin and that a good quality signal
ground is connected to the opposite side of the RBIAS
resistor. Do not connect any other components to this pin as
this would negatively impact performance. Capacitance on
this pin would create instabilities and should be avoided.
Start-Up Operation - CLK_EN# and PGOOD
The ISL6266A provides a 3.3V logic output pin for
CLK_EN#. The 3V3 pin allows for a system 3.3V source to
be connected to separated circuitry inside the ISL6266A,
solely devoted to the CLK_EN# function. The output is a
3.3V CMOS signal with 4mA sourcing and sinking capability.
This implementation removes the need for an external
pull-up resistor on this pin, thereby removing a leakage path
from the 3.3V supply to ground when the logic state is low.
The lack of superfluous current leakage paths serves to
prolong battery life. For noise immunity, the 3.3V supply
should be decoupled to digital ground rather than to analog
ground.
As mentioned in “Theory of Operation” on page 18,
CLK_EN# is logic level high at start-up until approximately
43µs after the V
Afterwards, CLK_EN# transitions low, triggering an internal
timer for the IMVP6_PWRGD signal. When the timer
reaches 6.8ms, IMVP-6_PWRGD will toggle high.
C
C
dV
-------
dt
SOFT
SOFT
SOFT
=
-------------------
C
will then control the start-up slewrate as well. One
SOFT
=
=
I
SS
SOFT
205μA
----------------------------------- -
SLEWRATE
=
I
GV
is as shown in Equation 5.
---------------------- -
0.015μF
CC_CORE
⁄
41μA
(
10mV 1μs
⁄
=
is in regulation at the Boot level.
2.8mV μs
)
⁄
GV
value given in the
SOFT
GV
June 14, 2010
) by
value
(EQ. 4)
(EQ. 5)
(EQ. 6)
FN6398.3