DPA424PN Power Integrations, DPA424PN Datasheet
DPA424PN
Specifications of DPA424PN
Available stocks
Related parts for DPA424PN
DPA424PN Summary of contents
Page 1
DPA423-426 DPA-Switch Highly Integrated DC-DC Converter ICs for Power over Ethernet & Telecom DC-DC Product Highlights Highly Integrated Solution • Eliminates 20-50 external components–saves space, cost • Integrates 220 V high frequency MOSFET, PWM control • Lower cost plastic DIP ...
Page 2
DPA423-426 Functional Block Diagram ....................................................................................................................................... 3 Pin Functional Description ...................................................................................................................................... 3 DPA-Switch Family Functional Description ............................................................................................................ 4 CONTROL (C) Pin Operation .................................................................................................................................. 4 Oscillator and Switching Frequency ....................................................................................................................... 5 Pulse Width Modulator & Maximum Duty Cycle ..................................................................................................... 6 Minimum Duty ...
Page 3
V C CONTROL ( SHUNT REGULATOR/ ERROR AMPLIFIER - + 5 (LIMIT) CURRENT LIMIT ADJUST START ON/OFF EXTERNAL CURRENT LIMIT ( LINE-SENSE ( OV/UV ...
Page 4
DPA423-426 DPA-Switch Family Functional Description DPA-Switch is an integrated switched mode power supply chip that converts a current at the control input to a duty cycle at the open drain output of a high voltage power MOSFET. During normal operation ...
Page 5
V, the control circuitry is activated and the soft-start begins. The soft-start circuit gradually increases the duty cycle of the MOSFET from zero to the maximum value over approximately 5 ms. The high voltage current source is turned ...
Page 6
DPA423-426 Pulse Width Modulator and Maximum Duty Cycle The pulse width modulator implements voltage mode control by driving the output MOSFET with a duty cycle inversely proportional to the current into the CONTROL pin that is in excess of the ...
Page 7
UV upper threshold has been reached again. Then, a soft-start will be initiated the next time CONTROL pin voltage reaches 5.8.V. If the power supply loses regulation before reaching the UV lower threshold, the device will enter auto-restart. At the ...
Page 8
DPA423-426 (typical), the CONTROL pin goes into the hysteretic mode of operation. In this mode, the CONTROL pin goes through alternate charge and discharge cycles between 4.8 V and 5.8 V (see CONTROL Pin Operation section above) and the IC ...
Page 9
Using Feature Pins FREQUENCY (F) Pin Operation The FREQUENCY pin is a digital input pin. Shorting the FREQUENCY pin to SOURCE pin selects the nominal switching frequency of 400 kHz (Figure 9) which is suited for most applications. For other ...
Page 10
DPA423-426 (Enabled) Output MOSFET Switching (Disabled) I (Default) LIMIT Current Limit -21.5 µA -25.5 µ Pin Voltage -250 -200 -150 -100 X Pin Current (µA) Note: These figures provide idealized functional characteristics with typical performance values. Please ...
Page 11
CONTROL (C) EXTERNAL CURRENT LIMIT (X) LINE-SENSE (L) Figure 8. LINE-SENSE (L), and EXTERNAL CURRENT LIMIT (X) Pin Input Simplified Schematic. DPA-Switch 230 µA (Negative Current Sense - ON/OFF, Current Limit Adjustment (Voltage Sense) 1 ...
Page 12
DPA423-426 Typical Uses of FREQUENCY (F) Pin + DC D Input CONTROL Voltage Figure 9. 400 kHz Frequency Operation. Typical Uses of LINE-SENSE (L) and EXTERNAL CURRENT LIMIT (X) Pins + DC Input Voltage D L CONTROL ...
Page 13
Typical Uses of LINE-SENSE (L) and EXTERNAL CURRENT LIMIT (X) Pins (cont Input Voltage CONTROL Figure 15. Externally Set Current Limit output or can be replaced by a manual ...
Page 14
DPA423-426 Typical Uses of LINE-SENSE (L) and EXTERNAL CURRENT LIMIT (X) Pins (cont.) + 619 kΩ Input CONTROL Voltage Figure 21. Active-on Remote ON/OFF with LINE-SENSE and EXTERNAL CURRENT ...
Page 15
Application Examples µH IN 2.5 A 36-75 VDC R1 619 kΩ 1% C1, C2 & µF 100 CONTROL CONTROL S X VR1 SMBJ 18.2 kΩ 150 V IN *Optional components Figure ...
Page 16
DPA423-426 + VDC J1 MΩ 619 kΩ 200 V C1 VR1 1 µF D SMAJ 100 V 150A CONTROL J1-2 Figure 26. A Cost ...
Page 17
L1 J1-1 PoE Interface 1 µH 2 VR51 28 V 500 mW R52 20 kΩ µF DC R51 100 V Input 24.9 kΩ Voltage 1% 1/4 W C51 D51 D52 BAV19 BAV19 ...
Page 18
DPA423-426 Key Application Considerations DPA-Switch Design Considerations Power Table This section provides a description of the assumptions used to generate the power tables (Tables 1 and 3 through 6) and explains how to use the information provided by them. All ...
Page 19
DPA425 would dissipate 0.5 W. Selecting DPA425 with associated reduced dissipation would increase overall converter efficiency by approximately 2%. Issues Affecting Dissipation: 1) Using synchronous rectification will tend to reduce device dissipation. 2) Designs with lower output voltages ...
Page 20
DPA423-426 the input decoupling capacitor. The SOURCE pin should not be used to return the power currents; incorrect operation of the device may result. The SOURCE is only intended as a signal ground. The device tab (SOURCE) is the correct ...
Page 21
Solder Side Component Side TOP VIEW V + DPA-Switch - V Maximize hatched copper area for optimum heat sinking Via between board layers V Figure 28. Layout Considerations for DPA-Switch Using S-PAK or R Package. Top Side PCB Bottom Side ...
Page 22
DPA423-426 DRAIN Voltage .................................. ................ -0 220 V DRAIN Peak Current: DPA423......................................1.75 A DPA424....................................... 3.5 A DPA425........................................... 7A DPA426....................................... 9.6 A CONTROL Voltage ................................................ -0 CONTROL Current .................................................... 100 mA LINE SENSE Pin Voltage ...
Page 23
Parameter Symbol CONTROL FUNCTIONS (cont.) Softstart Time t SOFT PWM Gain DC reg PWM Gain Temperature Drift Dynamic Z Impedance C Dynamic Impedance Temperature Drift CONTROL Pin Internal Filter Pole SHUTDOWN/AUTO-RESTART CONTROL Pin I Charging Current C(CH) Charging Current Temperature ...
Page 24
DPA423-426 Parameter Symbol LINE-SENSE (L) AND EXTERNAL CURRENT LIMIT (X) INPUTS (cont.) Line Overvoltage or Remote ON/ OFF Threshold I OV Current and Hysteresis (L Pin) Remote ON/OFF Negative Thresh- old Current and I REM Hysteresis (X Pin) L Pin ...
Page 25
Parameter Symbol FREQUENCY (F) INPUT FREQUENCY Pin V Threshold Voltage F FREQUENCY Pin I Input Current F FREQUENCY Pin t Delay Time delay(VF) CIRCUIT PROTECTION Self Protection Current Limit (See I LIMIT Note B) Initial Current I Limit INIT Leading ...
Page 26
DPA423-426 Parameter Symbol OUTPUT (cont.) Breakdown BV Voltage DSS Rise Time t R Fall Time t F SUPPLY VOLTAGE CHARACTERISTICS DRAIN Supply Voltage Shunt Regulator V Voltage C(SHUNT) Shunt Regulator Temperature Drift CONTROL I CD1 Supply/Discharge Current I CD2 NOTES: ...
Page 27
DRAIN VOLTAGE Figure 30. Duty Cycle Measurement. 120 100 Dynamic 1 = Impedance Slope CONTROL Pin Voltage (V) Figure 31. CONTROL Pin I-V Characteristic 470 Ω 0-15 V ...
Page 28
DPA423-426 BENCH TEST PRECAUTIONS FOR EVALUATION OF ELECTRICAL CHARACTERISTICS The following precautions should be followed when testing DPA-Switch by itself outside of a power supply. The schematic shown in Figure 33 is suggested for laboratory testing of DPA-Switch. When the ...
Page 29
Typical Performance Characteristics (cont.) 1.2 1.0 0.8 0.6 0.4 0.2 0 -50 - Junction Temperature (°C) Figure 36. Frequency vs. Temperature. 1.2 1.0 0.8 0.6 0.4 0.2 0 -50 - Junction Temperature (°C) Figure ...
Page 30
DPA423-426 Typical Performance Characteristics (cont.) 1 1.375 - I x 843 kΩ 1.4 ≤ ≤ -200 µA -25 µ 1.2 1.0 0.8 0.6 0.4 0.2 0 -225 -175 -125 -250 -200 -150 -100 EXTERNAL ...
Page 31
Typical Performance Characteristics (cont Scaling Factors: T DPA423 = 0.18 CASE 16 DPA424 = 0.36 DPA425 = 0.72 14 DPA426 = 1. Drain Voltage (V) Figure 48. ...
Page 32
DPA423-426 DIM inches mm A 0.367-0.387 9.32-9.83 B 0.240-0.260 6.10-6.60 C 0.125-0.145 3.18-3.68 G 0.015-0.040 0.38-1.02 H 0.120-0.140 3.05-3.56 J1 0.057-0.068 1.45-1.73 J2 0.014-0.022 0.36-0.56 K 0.008-0.015 0.20-0.38 L 0.100 BSC 2.54 BSC M 0.030 (MIN) 0.76 (MIN) N 0.300-0.320 ...
Page 33
Ref .024 (0.61) .034 (0.86) .315 (8.00) .380 (9.65) .638 (16.21) .050 (1.27) .038 (0.97) TO-263-7C .245 (6.22) MIN .225 (5.72) MIN .580 (14.73) ...
Page 34
DPA423-426 9.25 (0.364) A 9.55 (0.376) 0.75 (0.029) 1.30 (0.051) 7.85 (0.309) 8.15 (0.321) PIN #1 6X 0.63-0.89 (0.025-0.035) 0.25 (0.010 1.75 (0.069) 2.05 (0.081) 6X 0.10 (0.004) C Notes: 1. JEDEC reference: MO-169. 2. ...
Page 35
Revision Notes F 1) Final release data sheet Updated Figure 25 and text description Corrected missing text on page 9 and corrected Table 4. 2) Updated R package description. 3) Revised thermal impedances (θ 4) Updated ...
Page 36
... For the latest updates, visit our website: www.powerint.com Power Integrations reserves the right to make changes to its products at any time to improve reliability or manufacturability. Power Integrations does not assume any liability arising from the use of any device or circuit described herein. POWER INTEGRATIONS MAKES NO WARRANTY HEREIN AND SPECIFICALLY DISCLAIMS ALL WARRANTIES INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS ...