AD581KH Analog Devices Inc, AD581KH Datasheet - Page 6

• Manufacturer Part Number: AD581KH
• Description: IC PREC VOLT REF 10V TO-5-3
• Manufacturer: Analog Devices Inc
• Type: Voltage Referencer

Specifications of AD581KH

• Temperature Coefficient: 15ppm/°C
• Reference Type: Series
• Voltage - Output: 10V
• Tolerance: ±10mV
• Voltage - Input: 12 ~ 30 V
• Number Of Channels: 1
• Current - Quiescent: 1mA
• Current - Output: 10mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: TO-5-3, Metal Can
• Topology: Series
• Input Voltage: 12V To 30V
• Reference Voltage: 10V
• Reference Voltage Tolerance: 10mV
• No. Of Pins: 3
• Operating Temperature Range: 0°C To +70°C
• Current, Output: 10 mA
• Current, Quiescent Supply: 0.75 mA (Typ.) @ 25 °C
• Current, Short Circuit: 30 mA (Typ.) @ 25 °C
• Current, Supply: 0.75 mA
• Load Regulation: 200 uV⁄mA (Typ.) @ 25 °C
• Package Type: TO-5
• Power Dissipation: 600 mW
• Regulation, Line: 3 mV
• Regulation, Load: 200 μV/mA
• Standards: MIL-STD-883
• Temperature, Operating, Maximum: 150 °C
• Temperature, Operating, Minimum: -65 °C
• Temperature, Operating, Range: -65 to +150 °C
• Voltage, Input: 15 V
• Voltage, Noise: 40 μVp-p
• Voltage, Output: ±6.5 (Max.) @ 25 °C
• Voltage, Supply: 12 to 30 V
• Low Quiescent Current: 1.0 mA max
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Cathode: -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

AD581
APPLYING THE AD581
The AD581 is easy to use in virtually all precision reference
applications. The three pins are simply: primary supply, ground,
and output, with the case grounded. No external components
are required even for high precision applications; the degree of
desired absolute accuracy is achieved simply by selecting the
required device grade. The AD581 requires less than 1 mA quies-
cent current from an operating supply range of 13 V to 30 V.
An external fine trim may be desired to set the output level to
exactly 10.000 V within less than a millivolt (calibrated to a
main system reference). System calibration may also require a
reference slightly different from 10.00 V. In either case, the
optional trim circuit shown in Figure 3 can offset the output by
up to ±30 mV (with the 22 Ω resistor), if needed, with minimal
effect on other device characteristics.
3.9Ω
22Ω
12Ω
R
RANGE
±30mV
±10mV
±5mV
TRIM
Figure 3. Optional Fine Trim Configuration
Figure 2. Pin Configuration (Bottom View)
–15V
3.5ppm/°C
2.0ppm/°C
0.6ppm/°C
Δ TCR
AD581
MAX
13V TO 30V
4.3kΩ
GND
6.8kΩ
+V
10kΩ
S
V
OUT
AD581
10V
+15V
GND
+V
S
R
V
OUT
+10V
Rev. C | Page 6 of 12
VOLTAGE VARIATION vs. TEMPERATURE
Some confusion exists in the area of defining and specifying
reference voltage error over temperature. Historically, references
have been characterized using a maximum deviation per degree
Celsius; that is, 10 ppm/°C. However, because of nonlinearities
in temperature characteristics, which originated in standard
Zener references (such as S-type characteristics) manufacturers
opt for the maximum limit error band approach to specify devices.
This technique involves measurement of the output at three,
five, or more different temperatures to guarantee that the output
voltage falls within the given error band. The temperature charac-
teristic of the AD581 consistently follows the S-curve shown in
Figure 5. Three-point measurement of each device guarantees
the error band over the specified temperature range.
Q10
Q3
Q16
R40
10.005
10.000
9.995
R39
–55
Q4
–50
C51
Figure 5. Typical Temperature Characteristic
–40 –30 –20 –10 0
C52
Q6
Figure 4. Simplified Schematic
Q13
C50
Q12
TEMPERATURE (°C)
10 20 30 40 50 60 70 80 90 100 110 120 125
Q11
Q14
R41
Q20
Q2
R33
R30
Q15
Q8
Q1
R31
Q5
R32
Q7
R42
R34
R37
R35
R36
10V
V+
V–