ADR1581BRTZ-R2 Analog Devices Inc, ADR1581BRTZ-R2 Datasheet - Page 8
![IC VREF PREC SHUNT 1.25V SOT23-3](/photos/7/50/75089/sot-23-3_pkg_sml.jpg)
ADR1581BRTZ-R2
Manufacturer Part Number
ADR1581BRTZ-R2
Description
IC VREF PREC SHUNT 1.25V SOT23-3
Manufacturer
Analog Devices Inc
Datasheet
1.ADR1581ARTZ-REEL7.pdf
(12 pages)
Specifications of ADR1581BRTZ-R2
Temperature Coefficient
50ppm/°C
Package / Case
SOT-23-3, TO-236-3, Micro3™, SSD3, SST3
Mounting Type
Surface Mount
Current - Output
10mA
Voltage - Output
1.25V
Operating Temperature
-40°C ~ 85°C
Tolerance
±0.12%
Number Of Channels
1
Reference Type
Shunt
Current - Cathode
60µA
Topology
Shunt
Reference Voltage
1.25V
Reference Voltage Tolerance
1mV
Voltage Reference Case Style
SOT-23
No. Of Pins
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Input
-
Current - Quiescent
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
ADR1581
OUTPUT IMPEDANCE VS. FREQUENCY
Understanding the effect of the reverse dynamic output impedance
in a practical application is important to successfully applying the
ADR1581. A voltage divider is formed by the ADR1581 output
impedance and the external source impedance. When an external
source resistor of about 30 kΩ (I
noise from a 100 kHz switching power supply is developed at
the output of the ADR1581. Figure 15 shows how a 1 μF load
capacitor connected directly across the ADR1581 reduces the
effect of power supply noise to less than 0.01%.
NOISE PERFORMANCE AND REDUCTION
The noise generated by the ADR1581 is typically less than
5 μV p-p over the 0.1 Hz to 10 Hz band.
0.1 Hz to 10 Hz noise of a typical ADR1581. Noise in a 10 Hz to
10 kHz bandwidth is approximately 20 μV rms (see Figure 17a).
If further noise reduction is desired, a one-pole low-pass filter
can be added between the output pin and ground. A time constant
of 0.2 ms has a −3 dB point at about 800 Hz and reduces the high
frequency noise to about 6.5 μV rms (see
constant of 960 ms has a −3 dB point at 165 Hz and reduces the
high frequency noise to about 2.9 μV rms (see Figure 17c).
1µV/DIV
100
0.1
1k
10
1
10
ΔI
I
I
R
R
R
= 100µA
= 1mA
Figure 15. Output Impedance vs. Frequency
= 0.1I
Figure 16. 0.1 Hz to 10 Hz Voltage Noise
100
R
FREQUENCY (Hz)
1k
TIME (1s/DIV)
R
= 100 μA) is used, 1% of the
10k
Figure 16 shows the
Figure 17b). A time
C
100k
L
4.48µV p-p
= 0
C
L
= 1µF
1M
Rev. 0 | Page 8 of 12
TURN-ON TIME
Many low power instrument manufacturers are becoming
increasingly concerned with the turn-on characteristics of the
components in their systems. Fast turn-on components often
enable the end user to keep power off when not needed, and yet
those components respond quickly when the power is turned
on for operation. Figure 18 displays the turn-on characteristics
of the ADR1581.
Upon application of power (cold start), the time required for the
output voltage to reach its final value within a specified error is
the turn-on settling time. Two components normally associated
with this are time for active circuits to settle and time for thermal
gradients on the chip to stabilize. This characteristic is generated
from cold start operation and represents the true turn-on wave-
form after power-up.
turn-on settling characteristics of the device; the total settling
time to within 1.0 mV is about 6 μs, and there is no long thermal
tail when the horizontal scale is expanded to 2 ms/div.
20µV/DIV
10µV/DIV
10ms/DIV
V
0V
IN
Figure 19. Turn-On, Settling, and Transient Test Circuit
2.4V
250mV/DIV
R
40µV/DIV
S
= 11.5kΩ
Figure 18. Turn-On Response Time
Figure 17. Total RMS Noise
Figure 20 shows both the coarse and fine
6.5µV rms, t = 0.2ms
V
+
–
2.90µV rms, t = 960ms
R
5µs/DIV
21µV rms
V
C
R
IN
L
L
= 200pF
C
L
V
OUT
(a)
(b)
(c)