LT1031BMH Linear Technology, LT1031BMH Datasheet
LT1031BMH
Specifications of LT1031BMH
Available stocks
Related parts for LT1031BMH
LT1031BMH Summary of contents
Page 1
... The LT1031 can be used as a plug-in replacement for the AD581 and LH0070, * with improved electrical and thermal performance. , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. *See LH0070 Electrical Characteristics table and AD581 cross reference guide. ...
Page 2
... BOTTOM VIEW INPUT 1 2 OUTPUT 3 GROUND H PACKAGE 3-LEAD TO-39 METAL CAN = 150 C/ C/W (LH0070 150 C/ C/W (LT1031M 150 C/ C/W (LT1031C LT1031BMH LT1031CCH LT1031DMH LT1031DCH LT1031BCH LT1031 MIN TYP MAX UNITS 9.995 10.000 10.005 9.990 10.000 10.010 9.980 10.000 10.020 3 5 ppm/°C ...
Page 3
... Separate tests are done for hot and cold: T MIN ° Incremental slope is also measured For LT1031BMH, the 5ppm/°C drift specification is for – 25°C to 85°C. Drift over the full – 55°C to 125°C range is guaranteed to 7ppm/°C. ● (LH0070) The denotes the specifications which apply over the full = 10kΩ ...
Page 4
... Start-Up (Shunt Mode –12V 1k V OUT 0V 7 OUT GND TIME (µs) LT1031 • TPC05 order LT1031DCH order LT1031CCH order LT1031BCH order LT1031DMH order LT1031BMH Minimum Input Voltage 11 125°C J GUARANTEED 11.4 CURVE-ALL T = –55°C J TEMPS 11 25°C J 11.0 10.8 10.6 10.4 10.2 10 ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS Output Voltage Noise OUT FILTER = 1 POLE 0.1Hz LOW 100 1k 10k BANDWIDTH (Hz) LT1031 • TPC07 ...
Page 6
LT1031/LH0070 W U TYPICAL PERFOR A CE CHARACTERISTICS U U APPLICATIO S I FOR ATIO Trimming Output Voltage The LT1031 output can be trimmed by driving the ground pin. The suggested method is shown in the illustration below. A 5Ω ...
Page 7
U U APPLICATIO S I FOR ATIO Capacitive Loading and Transient Response The LT1031 is stable with all capacitive loads, but for optimum settling with load transients, output capacitance should be under 1000pF. The output stage of the reference is ...
Page 8
LT1031/LH0070 U U APPLICATIO S I FOR ATIO There is nothing magical about foam cups—any enclosure which blocks air flow from the reference will do. Smaller enclosures are better since they do not allow the build-up of internally generated air ...
Page 9
U APPLICATIO CIRCUITS R1 357Ω 1/2W LT1031 IN OUT 15V GND 6 LM301A 1 100pF R1** 253k R8 10M R9 100k R3 392k 1% –15V Strain Gauge Conditioner for 350Ω Bridge 28mA 28.5mA 5V 350Ω STRAIN R3 GUAGE ...
Page 10
LT1031/LH0070 U APPLICATIO CIRCUITS 2-Pole Lowpass Filtered Reference MYLAR V 1µF IN – R1 LT1031 LT1001 36k + IN OUT R2 36k GND f = 10Hz 0.5µF MYLAR Negative Shunt Reference Driven by Current Source LT1031 OUT ...
Page 11
... EQUIVALENT SCHEMATIC Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. Precision DAC Reference with System TC Trim OUT 8 ...
Page 12
... AND .050" BELOW THE REFERENCE PLANE ** FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS www.linear.com ● .165 – .185 (4.191 – 4.699) .500 (12.700) MIN .100 (2.540) H3(TO-39) 0801 .016 – .024 (0.406 – 0.610) LT 1105 REV B • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2005 1031fb ...