LT1021BCN8-5 Linear Technology, LT1021BCN8-5 Datasheet
LT1021BCN8-5
Specifications of LT1021BCN8-5
Available stocks
Related parts for LT1021BCN8-5
LT1021BCN8-5 Summary of contents
Page 1
... The LT1021-5 and LT1021- 10 are intended for systems requiring a precise 5V or 10V reference with an initial tolerance as low as ±0.05%. , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. LT1021 (7 AND 10 ONLY) ...
Page 2
... Lead Temperature (Soldering, 10 sec)................ 300° NC OUT TRIM ** *CONNECTED INTERNALLY. DO NOT CONNECT EXTERNAL CIRCUITRY TO THESE PINS. **NO TRIM PIN ON LT1021-7. DO NOT CONNECT EXTERNAL CIRCUITRY TO PIN 5 ON LT1021-7 = 45°C ORDER PART NUMBER LT1021DCH-5 LT1021BCN8-5 LT1021DMH-5 LT1021CCN8-5 LT1021BCH-7 LT1021CIN8-5 LT1021BMH-7 LT1021DCN8-5 LT1021DCH-7 LT1021DIN8-5 LT1021DMH-7 LT1021BCN8-7 LT1021BCH-10 LT1021DCN8-7 LT1021CMH-10 ...
Page 3
ELECTRICAL C HARA TERISTICS C range, otherwise specifications are T = 25° PARAMETER Output Voltage (Note 2) Output Voltage Temperature Coefficient (Note 3) Line Regulation (Note 4) Load Regulation (Sourcing Current) Load Regulation (Sinking Current) Supply Current Output ...
Page 4
LT1021 ELECTRICAL C HARA TERISTICS C range, otherwise specifications are T = 25° PARAMETER Output Voltage (Note 2) Output Voltage Temperature Coefficient (Note 3) Line Regulation (Note 4) Load Regulation (Sourcing Current) Load Regulation (Shunt Mode) Supply Current ...
Page 5
W U TYPICAL PERFOR A Ripple Rejection 115 f = 150Hz LT1021-7 110 LT1021-10 105 100 LT1021 INPUT VOLTAGE (V) LT1021 G01 Start-Up (Series Mode ...
Page 6
LT1021 W U TYPICAL PERFOR A Quiescent Current LT1021-5 1 OUT 1.6 1.4 1 – 55° 25° 125°C J 0.6 0.4 0 ...
Page 7
W U TYPICAL PERFOR A Shunt Characteristics LT1021-7 1.2 INPUT PIN OPEN 1.0 0 – 55° 25°C J 0.6 0 125° ...
Page 8
LT1021 W U TYPICAL PERFOR A Shunt Characteristics LT1021-10 1.8 INPUT PIN OPEN 1.6 1.4 1.2 1 – 55° 25°C 0 125° ...
Page 9
U U APPLICATIONS INFORMATION Effect of Reference Drift on System Accuracy A large portion of the temperature drift error budget in many systems is the system reference voltage. This graph indicates the maximum temperature coefficient allowable if the reference is ...
Page 10
LT1021 U U APPLICATIONS INFORMATION minimized. In the current output circuit, R1 determines output current. It should have a TC commensurate with the LT1021 or track closely with the feedback resistor around the op amp. LT1021-7 IN OUT R2* GND ...
Page 11
U U APPLICATIONS INFORMATION Effects of Air Movement on Low Frequency Noise The LT1021 has very low noise because of the buried zener used in its design. In the 0.1Hz to 10Hz band, peak-to-peak noise is about 0.5ppm of the ...
Page 12
LT1021 U TYPICAL APPLICATIONS Boosted Output Current with No Current Limit + ≥ 1.8V) OUT R1 220Ω 2N2905 IN LT1021 10V AT OUT 100mA GND + 2µF SOLID TANT 1021 TA05 2-Pole Lowpass Filtered Reference 1µF MYLAR ...
Page 13
U TYPICAL APPLICATIONS Strain Gauge Conditioner for 350Ω Bridge R1 357Ω 1/2W 28mA LT1021-10 28.5mA 15V IN OUT GND † LM301A 2 – 1 100pF 8 * THIS RESISTOR PROVIDES POSITIVE FEEDBACK TO THE BRIDGE TO ELIMINATE ...
Page 14
LT1021 U TYPICAL APPLICATIONS R1** 253k R8 10M R9 100k R3 392k 1% –15V U W EQUIVALE T SCHE ATIC 14 Ultralinear Platinum Temperature Sensor* LT1021-10 IN 20V OUT GND R2* R10 5k 182k 1% R11 6.65M 1% ...
Page 15
... MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 16
... MSOP www.linear.com ● .189 – .197 (4.801 – 5.004) NOTE .150 – .157 (3.810 – 3.988) NOTE .004 – .010 (0.101 – 0.254) .050 (1.270) BSC SO8 0303 LT 1005 REV C • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 1995 1021fc ...