REF194GSZ Analog Devices Inc, REF194GSZ Datasheet - Page 22
![IC VOLT REF MICROPWR 4.5V 8SOIC](/photos/5/66/56684/505-8-soic_sml.jpg)
REF194GSZ
Manufacturer Part Number
REF194GSZ
Description
IC VOLT REF MICROPWR 4.5V 8SOIC
Manufacturer
Analog Devices Inc
Series
REF19r
Datasheet
1.REF195GPZ.pdf
(28 pages)
Specifications of REF194GSZ
Temperature Coefficient
25ppm/°C
Reference Type
Series
Voltage - Output
4.5V
Tolerance
±10mV
Voltage - Input
3 ~ 15 V
Number Of Channels
1
Current - Quiescent
45µA
Current - Output
30mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Topology
Series
Input Voltage
4.75V To 15V
Reference Voltage
4.5V
Reference Voltage Tolerance
2mV
Voltage Reference Case Style
SOIC
No. Of Pins
8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Cathode
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
REF194GSZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
REF194GSZ-REEL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
REF19x Series
management should still be exercised. A short, heavy, low dc
resistance (DCR) conductor should be used from U1 to 6 to the V
Sense Point S, where the collector of Q1 connects to the load, Point F.
Because of the current limiting configuration, the dropout voltage
circuit is raised about 1.1 V over that of the REF19x devices, due to
the V
However, overall dropout is typically still low enough to allow
operation of a 5 V to 3.3 V regulator/reference using the REF196 for
U1 as noted, with a V
The requirement for a heat sink on Q1 depends on the maximum
input voltage and short-circuit current. With V
300 mA current limit, the worst-case dissipation of Q1 is 1.5 W,
less than the TO-220 package 2 W limit. However, if smaller TO-39
or TO-5 package devices, such as the 2N4033, are used, the current
limit should be reduced to keep maximum dissipation below
the package rating. This is accomplished by simply raising R4.
A tantalum output capacitor is used at C1 for its low equivalent
series resistance (ESR), and the higher value is required for stability.
Capacitor C2 provides input bypassing and can be an ordinary
electrolytic.
Shutdown control of the booster stage is an option, and when used,
some cautions are needed. Due to the additional active devices
in the V
unbuffered REF19x device. To enable shutdown control, the
connection from U1 to Q2 is broken at the X, and Diode D1
then allows a CMOS control source, V
operation. Startup from shutdown is not as clean under heavy
load as it is in basic REF19x series, and can require several
milliseconds under load. Nevertheless, it is still effective and
can fully control 150 mA loads. When shutdown control is
used, heavy capacitive loads should be minimized.
NEGATIVE PRECISION REFERENCE WITHOUT
PRECISION RESISTORS
In many current-output CMOS DAC applications where the output
signal voltage must be the same polarity as the reference voltage, it
is often necessary to reconfigure a current-switching DAC into
a voltage-switching DAC using a 1.25 V reference, an op amp,
and a pair of resistors. Using a current-switching DAC directly
requires an additional operational amplifier at the output to
reinvert the signal. A negative voltage reference is then desirable
because an additional operational amplifier is not required for
either reinversion (current-switching mode) or amplification
(voltage-switching mode) of the DAC output voltage. In general,
any positive voltage reference can be converted into a negative
voltage reference using an operational amplifier and a pair of
matched resistors in an inverting configuration. The disadvantage
to this approach is that the largest single source of error in the
circuit is the relative matching of the resistors used.
The circuit illustrated in Figure 26 avoids the need for tightly
matched resistors by using an active integrator circuit. In this
circuit, the output of the voltage reference provides the input
drive for the integrator. To maintain circuit equilibrium, the
BE
S
of Q1 and the drop across Current Sense Resistor R4.
line to U1, a direct drive to Pin 3 does not work as with an
S
as low as 4.5 V and a load current of 150 mA.
C
, to drive U1 to 3 for on/off
S
= 5 V and a
Rev. K | Page 22 of 28
OUT
integrator adjusts its output to establish the proper relationship
between the V
output voltage can be selected by substituting for the appropriate
reference IC. The sleep feature is maintained in the circuit with
the simple addition of a PNP transistor and a 10 kΩ resistor.
One caveat to this approach is that although rail-to-rail output
amplifiers work best in the application, these operational amplifiers
require a finite amount (mV) of headroom when required to provide
any load current; consider this issue when choosing the negative
supply for the circuit.
STACKING REFERENCE ICs FOR ARBITRARY
OUTPUTS
Some applications may require two reference voltage sources that
are a combined sum of standard outputs. The circuit in Figure 27
shows how this stacked output reference can be implemented.
Two reference ICs are used, fed from a common unregulated input,
V
shown in Figure 27, which provide two output voltages, V
V
sum of this voltage and the terminal voltage of U2. U1 and U2
are chosen for the two voltages that supply the required outputs
(see Table 1). If, for example, both U1 and U2 are REF192s, the
two outputs are 2.5 V and 5.0 V.
TTL/CMOS
Figure 26. Negative Precision Voltage Reference Uses No Precision Resistors
+V
V
V
COMMON
SLEEP
S
OUT2
S
IN
. The outputs of the individual ICs are connected in series, as
S
> V
. V
OUT2
10kΩ
10kΩ
OUT1
Figure 27. Stacking Voltage References with the REF19x
0.1µF
0.1µF
+ 0.15V
C1
C3
2N3906
is the terminal voltage of U1, whereas V
OUT
3
and GND references. Thus, any desired negative
SLEEP
3
3
REF19x
(SEE TABLE)
(SEE TABLE)
REF19x
REF19x
GND
V
V
2
4
OUTPUT
U2
U1
S
S
2
4
2
4
U1/U2
REF192/REF192
REF192/REF194
REF192/REF195
100kΩ
6
6
V
V
6
O
O
(U2)
(U1)
OUTPUT TABLE
1kΩ
1µF
+
+
C2
1µF
C4
1µF
V
2.5
2.5
2.5
OUT1
A1
A1 = 1/2 OP295,
+5V
–5V
R1
3.9kΩ
(SEE TEXT)
(V)
1µF
1/2 OP291
V
5.0
7.0
7.5
OUT2
100Ω
OUT2
+V
+V
V
COMMON
(V)
OUT
OUT1
OUT2
OUT1
is the
and
–V
REF