TC9402CPD Microchip Technology, TC9402CPD Datasheet - Page 9

• Manufacturer Part Number: TC9402CPD
• Description: IC V-FREQ/FREQ-V CONV 14DIP
• Manufacturer: Microchip Technology
• Type: Volt to Freq & Freq to Voltr

Specifications of TC9402CPD

• Package / Case: 14-DIP (0.300", 7.62mm)
• Frequency - Max: 100kHz
• Full Scale: ±100ppm/°C
• Linearity: ±0.25%
• Mounting Type: Through Hole
• Supply Voltage (max): 15 V
• Supply Voltage (min): 8 V
• Maximum Operating Temperature: 70 C
• Minimum Operating Temperature: 0 C
• Dual Supply Voltage: +/- 5 V
• Full Scale Frequency: 100 KHz
• Linearity Error: +/- 0.5 % FSR
• Maximum Dual Supply Voltage: +/- 7.5 V
• Minimum Dual Supply Voltage: +/- 4 V
• Mounting Style: Through Hole
• Operating Supply Voltage: 9 V or 12 V
• Frequency: 100kHz
• Full Scale Range: 1Hz To 100kHz
• Linearity %: 0.25%
• Supply Voltage Range: ± 4V To ± 7.5V
• Digital Ic Case Style: DIP
• No. Of Pins: 14
• Frequency Max: 100kHz
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 158-1142; 158-1142

4.3
This output is an open drain N-channel FET, which pro-
vides a square wave one-half the frequency of the
pulse frequency output. The FREQ/2 OUT output will
change state on the rising edge of PULSE FREQ OUT.
This output requires a pull-up resistor and interfaces
directly with MOS, CMOS, and TTL logic.
4.4
The sources of both the FREQ/2 OUT and the PULSE
FREQ OUT are connected to this pin. An output level
swing from the drain voltage to ground, or to the V
supply, may be obtained by connecting this pin to the
appropriate point.
4.5
An external resistor, connected to V
point for the TC9400. Specifications for the TC9400 are
based on R
noted.
Increasing the maximum frequency of the TC9400
beyond 100kHz is limited by the pulse width of the
pulse output (typically 3µsec). Reducing R
decrease the pulse width and increase the maximum
operating frequency, but linearity errors will also
increase. R
typically produce a maximum full scale frequency of
500kHz.
4.6
This pin is the output stage of the operational amplifier.
During V/F operation, a negative going ramp signal is
available at this pin. In the F/V mode, a voltage
proportional to the frequency input is generated.
4.7
This pin is the non-inverting input of the operational
amplifier. The low frequency set point is determined by
adjusting the voltage at this pin.
©
2002 Microchip Technology Inc.
Freq/2 Out
Output Common
R
Amplifier Out
Zero Adjust
BIAS
BIAS
BIAS
can be reduced to 20kΩ, which will
= 100kΩ ±10%, unless otherwise
SS
, sets the bias
BIAS
will
SS
4.8
The inverting input of the operational amplifier and the
summing junction when connected in the V/F mode. An
input current of 10µA is specified, but an over range
current up to 50µA can be used without detrimental
effect to the circuit operation. I
junction of an operational amplifier. Voltage sources
cannot be attached directly, but must be buffered by
external resistors.
4.9
A reference voltage from either a precision source, or
the V
TC9400 is dependent on the voltage regulation and
temperature characteristics of the reference circuitry.
Since the TC9400 is a charge balancing V/F converter,
the reference current will be equal to the input current.
For this reason, the DC impedance of the reference
voltage source must be kept low enough to prevent lin-
earity errors. For linearity of 0.01%, a reference imped-
ance of 200W or less is recommended. A 0.1µF bypass
capacitor should be connected from V
4.10
The charging current for C
pin. When the Op Amp output reaches the threshold
level, this pin is internally connected to the reference
voltage and a charge, equal to V
from the integrator capacitor. After about 3µsec, this pin
is internally connected to the summing junction of the
Op Amp to discharge C
ing ensures that the reference voltage is not directly
applied to the summing junction.
SS
TC9400/9401/9402
supply is applied to this pin. Accuracy of the
I
V
V
IN
REF
REF
Out
REF
. Break-before-make switch-
REF
IN
is supplied through this
REF
connects the summing
x C
DS21483B-page 9
REF
REF
to ground.
, is removed