DS1620 Maxim Integrated Products, DS1620 Datasheet - Page 6
![IC THERMOMETER/STAT DIG 8-DIP](/photos/1/39/13900/175-8-dip_sml.jpg)
DS1620
Manufacturer Part Number
DS1620
Description
IC THERMOMETER/STAT DIG 8-DIP
Manufacturer
Maxim Integrated Products
Datasheet
1.DS1620.pdf
(12 pages)
Specifications of DS1620
Function
Thermometer, Thermostat
Topology
Comparator, Register Bank
Sensor Type
Internal
Sensing Temperature
-55°C ~ 125°C
Output Type
Digital
Output Alarm
Yes
Output Fan
No
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-55°C ~ 125°C
Mounting Type
Through Hole
Package / Case
8-DIP (0.300", 7.62mm)
Full Temp Accuracy
+/- 2 C
Digital Output - Bus Interface
Serial (3-Wire)
Digital Output - Number Of Bits
9 bit
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 55 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS1620
Manufacturer:
DALLAS
Quantity:
5 510
Part Number:
DS1620
Manufacturer:
DALLAS
Quantity:
20 000
Part Number:
DS1620+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
DS1620S
Manufacturer:
DALLAS
Quantity:
4 225
Company:
Part Number:
DS1620S
Manufacturer:
DALLAS
Quantity:
140
Part Number:
DS1620S
Manufacturer:
DALLAS
Quantity:
20 000
Company:
Part Number:
DS1620S+
Manufacturer:
Maxim
Quantity:
4 127
Part Number:
DS1620S+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
DS1620S+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
DS1620
1SHOT = One–Shot Mode. If 1SHOT is 1, the DS1620 will perform one temperature conversion upon
reception of the Start Convert T protocol. If 1SHOT is 0, the DS1620 will continuously perform
2
temperature conversion. This bit is stored in nonvolatile E
memory, capable of at least 50,000 writes. The
DS1620 is shipped with 1SHOT=0.
For typical thermostat operation, the DS1620 will operate in continuous mode. However, for applications
where only one reading is needed at certain times or to conserve power, the one–shot mode may be used.
Note that the thermostat outputs (T
, T
, T
) will remain in the state they were in after the last
HIGH
LOW
COM
valid temperature conversion cycle when operating in one–shot mode.
OPERATION IN STAND–ALONE MODE
In applications where the DS1620 is used as a simple thermostat, no CPU is required. Since the
temperature limits are nonvolatile, the DS1620 can be programmed prior to insertion in the system. In
order to facilitate operation without a CPU, the CLK/
pin (pin 2) can be used to initiate
CONV
conversions. Note that the CPU bit must be set to 0 in the configuration register to use this mode of
operation. Whether CPU=0 or 1, the 3–wire port is active. Setting CPU=1 disables the stand–alone mode.
To use the CLK/
pin to initiate conversions,
must be low and CLK/
must be high. If
CONV
RST
CONV
CLK/
is driven low and then brought high in less than 10 ms, one temperature conversion will be
CONV
performed and then the DS1620 will return to an idle state. If CLK/
is driven low and remains low,
CONV
continuous conversions will take place until CLK/
is brought high again. With the CPU bit set to 0,
CONV
the CLK/
will override the 1SHOT bit if it is equal to 1. This means that even if the part is set for
CONV
one–shot mode, driving CLK/
low will initiate conversions.
CONV
3–WIRE COMMUNICATIONS
The 3–wire bus is comprised of three signals. These are the
(reset) signal, the CLK (clock) signal,
RST
and the DQ (data) signal. All data transfers are initiated by driving the
input high. Driving the
RST
RST
input low terminates communication. (See Figures 4 and 5.) A clock cycle is a sequence of a falling edge
followed by a rising edge. For data inputs, the data must be valid during the rising edge of a clock cycle.
Data bits are output on the falling edge of the clock and remain valid through the rising edge.
When reading data from the DS1620, the DQ pin goes to a high-impedance state while the clock is high.
Taking
low will terminate any communication and cause the DQ pin to go to a high-impedance
RST
state.
Data over the 3–wire interface is communicated LSB first. The command set for the 3–wire interface as
shown in Table 4 is as follows.
Read Temperature [AAh]
This command reads the contents of the register which contains the last temperature conversion result.
The next nine clock cycles will output the contents of this register.
Write TH [01h]
This command writes to the TH (HIGH TEMPERATURE) register. After issuing this command the next
nine clock cycles clock in the 9–bit temperature limit which will set the threshold for operation of the
T
output.
HIGH
6 of 12