MAX6501UKP065+T Maxim Integrated Products, MAX6501UKP065+T Datasheet - Page 6
![IC TEMP SWITCH SOT23-5](/photos/1/38/13898/175-sot-23-5_sml.jpg)
MAX6501UKP065+T
Manufacturer Part Number
MAX6501UKP065+T
Description
IC TEMP SWITCH SOT23-5
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX6504UKP005T.pdf
(9 pages)
Specifications of MAX6501UKP065+T
Function
Temp Switch
Topology
Comparator, Voltage Reference
Sensor Type
Internal
Sensing Temperature
65°C Trip Point
Output Type
Active Low/Open Drain
Output Alarm
Yes
Output Fan
Yes
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-55°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
SOT-23-5, SC-74A, SOT-25
Temperature Threshold
+ 65 C
Full Temp Accuracy
+/- 0.5 C
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 55 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
The MAX6501–MAX6504 supply current is typically
30µA. When used to drive high-impedance loads, the
devices dissipate negligible power. Therefore, the die
temperature is essentially the same as the package
temperature. The key to accurate temperature monitor-
ing is good thermal contact between the MAX6501–
MAX6504 package and the device being monitored. In
some applications, the SOT23 package may be small
enough to fit underneath a socketed µP, allowing the
device to monitor the µP’s temperature directly. Use the
monitor’s output to reset the µP, assert an interrupt, or
trigger an external alarm.
Accurate temperature monitoring depends on the ther-
mal resistance between the device being monitored
and the MAX6501–MAX6504 die. Heat flows in and out
of plastic packages, primarily through the leads. Pin 2
of the SOT23-5 package provides the lowest thermal
resistance to the die. Short, wide copper traces leading
to the temperature monitor ensure that heat transfers
quickly and reliably.
The rise in die temperature due to self-heating is given
by the following formula:
where P
MAX6501–MAX6504, and θ
resistance.
The typical thermal resistance is 140°C/W for the
SOT23 package. To limit the effects of self-heating,
minimize the output currents. For example, if the
MAX6501 or MAX6503 sink 1mA, the output voltage is
guaranteed to be less than 0.3V. Therefore, an addi-
tional 0.3mW of power is dissipated within the IC. This
corresponds to a 0.042°C shift in the die temperature in
the SOT23.
Low-Cost, +2.7V to +5.5V, Micropower
Temperature Switches in SOT23
Figure 2. Microprocessor Alarm/Reset
6
_______________________________________________________________________________________
+3.3V
DISSIPATION
V
μP
CC
SHUTDOWN
ΔT
Applications Information
J
RESET
= P
INT
OR
is the power dissipated by the
DISSIPATION
Thermal Considerations
JA
R
100kΩ
HEAT
PULLUP
is the package’s thermal
x θ
TOVER
HYST
JA
MAX6501
GND
V
CC
GND
The MAX6501–MAX6504 temperature switch outputs
assert when the die temperature is outside the factory-
programmed range. Combining the outputs of two
devices creates an over/undertemperature alarm. The
MAX6501/MAX6503 and the MAX6502/MAX6504 are
designed to form two complementary pairs, each con-
taining one cold trip-point output and one hot trip-point
output. The assertion of either output alerts the system to
an out-of-range temperature. The MAX6502/MAX6504
push/pull output stages can be ORed to produce a ther-
mal out-of-range alarm. More favorably, a MAX6501/
MAX6503 can be directly wire-ORed with a single exter-
nal resistor to accomplish the same task (Figure 4).
The temperature window alarms shown in Figure 4 can
be used to accurately determine when a device’s tem-
perature falls out of the -5°C to +75°C range. The ther-
mal-overrange signal can be used to assert a thermal
shutdown, power-up, recalibration, or other temperature-
dependent function.
In high-performance/high-reliability applications, multi-
ple temperature monitoring is important. The high-level
integration and low cost of the MAX6501–MAX6504
facilitate the use of multiple temperature monitors to in-
crease system reliability. Figure 5’s application uses
two MAX6502s with different temperature thresholds to
ensure that fault conditions that can overheat the moni-
tored device cause no permanent damage. The first
temperature monitor activates the fan when the die
temperature exceeds +45°C. The second MAX6502
triggers a system shutdown if the die temperature
reaches +75°C. The second temperature monitor’s out-
put asserts when a wide variety of destructive fault con-
ditions occur, including latchups, short circuits, and
cooling-system failures.
Figure 3. Overtemperature Fan Control
+5V
V
μP
CC
Temperature-Window Alarm
HEAT
GND
V
CC
Temperature Monitor
MAX6502
Low-Cost, Fail-Safe
GND
TOVER
HYST
FAN