LM99-1CIMM/NOPB National Semiconductor, LM99-1CIMM/NOPB Datasheet - Page 6

• Manufacturer Part Number: LM99-1CIMM/NOPB
• Description: IC REM DIODE TEMP SENSOR 8-MSOP
• Manufacturer: National Semiconductor

Specifications of LM99-1CIMM/NOPB

• Function: Hardware Monitor
• Topology: ADC (Sigma Delta), Comparator, Register Bank
• Sensor Type: External & Internal
• Sensing Temperature: 0°C ~ 125°C, External Sensor
• Output Type: SMBus™
• Output Alarm: Yes
• Output Fan: Yes
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: 0°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• For Use With: LM99-1EVAL/NOPB - BOARD EVALUATION LM99-1LM99-1EVAL - BOARD EVALUATION LM99-1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: LM99-1CIMM; LM99-1CIMMNOPB; LM99-1CIMMNOPBTR; LM99-1CIMMNOPBTR; LM99-1CIMMTR

www.national.com
SMBus Communication
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating
the device beyond its rated operating conditions.
Note 2: When the input voltage (V
Parasitic components and or ESD protection circuitry are shown in the figure below for the LM99’s pins. The nominal breakdown voltage of D3 is 6.5 V. Care should
be taken not to forward bias the parasitic diode, D1, present on pins: D+, D−. Doing so by more than 50 mV may corrupt a temperature measurement.
Note: An “x” indicates that the diode exists.
Note 3: See the URL ”http://www.national.com/packaging/“ for other recommendations and methods of soldering surface mount devices.
Note 4: Human body model, 100 pF discharged through a 1.5 kΩ resistor. Machine model, 200 pF discharged directly into each pin.
Note 5: Thermal resistance junction-to-ambient when attached to a printed circuit board with 2 oz. foil:
Note 6: Typicals are at T
Note 7: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 8: Local temperature accuracy does not include the effects of self-heating. The rise in temperature due to self-heating is the product of the internal power
dissipation of the LM99 and the thermal resistance. See (Note 5) for the thermal resistance to be used in the self-heating calculation.
Note 9: Quiescent current will not increase substantially with an SMBus.
Note 10: This specification is provided only to indicate how often temperature data is updated. The LM99 can be read at any time without regard to conversion state
(and will yield last conversion result).
Note 11: Default values set at power up.
Note 12: The output rise time is measured from (V
Note 13: The output fall time is measured from (V
Note 14: Holding the SMBData and/or SMBCLK lines Low for a time interval greater than t
SMBData and SMBCLK pins to a high impedance state.
Pin Name
V
D+
D−
T_CRIT_A
ALERT
SMBData
SMBCLK
DD
– MSOP-8 = 210˚C/W
PIN #
1
2
3
4
6
7
8
A
= 25˚C and represent most likely parametric norm.
I
) at any pin exceeds the power supplies (V
D1
x
x
D2
x
x
IN(1)
IN(0)
FIGURE 1. ESD Protection Input Structure
min - 0.15 V) to (V
max + 0.15 V) to (V
D3
D4
IN(1)
IN(1)
min + 0.15 V).
I
min − 0.15 V).
<
6
GND or V
D5
x
TIMEOUT
I
>
D6
V
x
x
DD
), the current at that pin should be limited to 5 mA.
will reset the LM99’s SMBus state machine, therefore setting
20053813
D7
x
x
x
x
x
R1
x
x
x
x
SNP
x
x
x
x
ESD CLAMP
20053840
x
x
x