LM96163CISD/NOPB National Semiconductor, LM96163CISD/NOPB Datasheet - Page 18

• Manufacturer Part Number: LM96163CISD/NOPB
• Description: IC TEMP SENSOR DGTL REMOTE 10LLP
• Manufacturer: National Semiconductor
• Series: PowerWise®, TruTherm®r

Specifications of LM96163CISD/NOPB

• Function: Fan Control, Temp Monitor
• Topology: ADC (Sigma Delta), Comparator, Register Bank, Tach
• Sensor Type: External & Internal
• Sensing Temperature: -40°C ~ 85°C, External Sensor
• Output Type: SMBus™
• Output Alarm: Yes
• Output Fan: Yes
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 10-LLP
• Temperature Sensor Function: Temp Sensor
• Interface Type: Serial (2-Wire)
• Resolution: 10+SignBit
• Package Type: LLP EP
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: LM96163CISDTR

www.national.com
[RESERVED] REGISTERS—NOT USED
Register
C0–FD
68–BE
1A–20
2.3 LM96163 REQUIRED INITIAL FAN CONTROL REGISTER SEQUENCE
Important! The BIOS or firmware must follow the sequence below to configure the following Fan Registers for the LM96163 before
using any of the Fan or Tachometer or PWM registers:
All other registers can be written at any time after the above sequence.
[HEX]
22–29
34–44
17-18
Step
0C
FF
06
15
1
2
3
4
5
6
7
Stepping/Die Rev. ID
Not Used
Not Used
Not Used
Not Used
Not Used
Not Used
Not Used
Not Used
Not Used
After power up check to make sure that the Not Ready bit is cleared in the POR Status register [33] bit 7.
Enable or disable Remote Diode TruTherm mode, [30] bit 1.
[4A] Write bits 0 and 1; 3 and 4. This includes tach settings if used, PWM internal clock select (1.4 kHz or 360 kHz) and
PWM Output Polarity.
[4B] Write bits 0 through 5 to program the spin-up settings.
[4D] Write bits 0 through 4 to set the frequency settings. This works with the PWM internal clock select. If 22.5 kHz is
selected then enhanced fan control functions such as Lookup Table transition smoothing with extended PWM duty cycle
resolution is available and should be setup [45].
Choose, then write, only one of the following:
A. [4F–67] the Lookup Table and [4E] the Lookup Table Offset, [45] Lookup Table Temperature Resolution can also be
modified
or
B. [4C] the PWM value bits 0 through 5 or bits 0 through 7 if extended duty cycle resolution is selected.
If Step 4A, Lookup Table, was chosen and written then write [4A] bit 5 PWPGM = 0. PWPGM should be set to 1 to enable
writing to the fan control registers listed in this table.
Register Name
[Register]
HEX
18
and Setup Instructions
Read/Write
Read Only
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
POR Default
[HEX]
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
49