MCP98243-BE/ST Microchip Technology, MCP98243-BE/ST Datasheet - Page 36

• Manufacturer Part Number: MCP98243-BE/ST
• Description: IC TEMP SENSOR 3V 2WIRE 8-TSSOP
• Manufacturer: Microchip Technology

Specifications of MCP98243-BE/ST

• Package / Case: 8-TSSOP
• Output Type: I²C™/SMBus™
• Function: Temp Monitoring System (Sensor)
• Topology: ADC (Sigma Delta), Register Bank
• Sensor Type: Internal
• Sensing Temperature: -40°C ~ 125°C
• Output Alarm: No
• Output Fan: Yes
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Temperature Threshold: + 125 C
• Full Temp Accuracy: 1 C
• Digital Output - Bus Interface: 2-Wire, SMBus, I2C
• Digital Output - Number Of Bits: 8 bit
• Supply Voltage (max): 6 V
• Supply Voltage (min): 1.8 V
• Description/function: Thermal Management ICs
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Current: 100 uA to 1100 uA
• Ic Output Type: Digital
• Sensing Accuracy Range: ± 0.5°C
• Temperature Sensing Range: -40°C To +125°C
• Supply Voltage Range: 2.7V To 5.5V
• Sensor Case Style: TSSOP
• No. Of Pins: 8
• Rohs Compliant: Yes
• Resolution (bits): 8bit
• Supply Voltage Min: 3V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

MCP9843/98243
5.3.2
The write Address Byte, word address and the first data
byte are transmitted to the MCP98243 in the same way
as in a byte write. Instead of generating a Stop
condition, the master transmits up to 15 additional data
bytes to the MCP98243, which are temporarily stored
in the on-chip page buffer and will be written into the
memory after the master has transmitted a Stop
condition. Upon receipt of each word, the four lower
order address pointer bits are internally incremented by
one. The higher order four bits of the word address
remain constant. If the master should transmit more
than 16 bytes prior to generating the Stop condition, the
address counter will roll over and the previously
received data will be overwritten. As with the byte write
operation, once the Stop condition is received, an
internal write cycle will begin
FIGURE 5-14:
DS22153C-page 36
SCL
SDA
PAGE WRITE
1
X
X
2
3
X
Data at (n)
S
Timing Diagram for Page Write (See Section 4.0 “Serial Communication”).
4
X
1
1
X
5
2
0
(Figure
X
6
Address Byte
3
1
X
7
MCP98243
4
X
0
8
5-14).
Note:
5
A
2
A
C
K
A
6
1
1
X
A
0
7
2
X
MCP98243
n is the initial address for a page.
Data at (n+1)
W
8
3
X
A
C
K
4
X
1
X
5
X
Word Address (n)
2
X
6
X
3
X
X
7
MCP98243
4
X
X
8
Note:
5
X
A
C
K
6
X
X
7
X
Page write operations are limited to writing
bytes within a single physical page,
regardless of the number of bytes actually
being written. Physical page boundaries
start at addresses that are integer
multiples of the page buffer size (or ‘page
size’) and end at addresses that are
integer multiples of [page size - 1]. If a
Page Write command attempts to write
across a physical page boundary, the
result is that the data wraps around to the
beginning of the current page (overwriting
data previously stored there), instead of
being written to the next page, as might be
expected. It is therefore necessary for the
application software to prevent page write
operations that would attempt to cross a
page boundary.
X
MCP98243
Data at (n+15)
X
8
X
A
C
K
© 2009 Microchip Technology Inc.
X
X
MCP98243
X
A
C
K
P