LTC1968CMS8 Linear Technology, LTC1968CMS8 Datasheet - Page 8
![IC CONVERTER RMS-DC PREC 8MSOP](/photos/6/57/65743/8-msop_05-08-1660_sml.jpg)
LTC1968CMS8
Manufacturer Part Number
LTC1968CMS8
Description
IC CONVERTER RMS-DC PREC 8MSOP
Manufacturer
Linear Technology
Datasheet
1.LTC1968CMS8PBF.pdf
(28 pages)
Specifications of LTC1968CMS8
Current - Supply
2.3mA
Voltage - Supply
5.0V
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC1968CMS8
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LTC1968CMS8#TRPBF
Manufacturer:
ST
Quantity:
2 100
APPLICATIO S I FOR ATIO
How an RMS-to-DC Converter Works
Monolithic RMS-to-DC converters use an implicit compu-
tation to calculate the RMS value of an input signal. The
fundamental building block is an analog multiply/divide
used as shown in Figure 3. Analysis of this topology is
easy and starts by identifying the inputs and the output of
LTC1968
currents. The power delivered to the load depends on the
firing angle, as well as any parasitic losses such as switch
“ON” voltage drop. Real circuit waveforms will also typi-
cally have significant ringing at the switching transition,
dependent on exact circuit parasitics. For the purposes of
this data sheet, “SCR Waveforms” refers to the ideal
chopped sine wave, though the LTC1968 will do faithful
RMS-to-DC conversion with real SCR waveforms as well.
The case shown is for Θ = 90°, which corresponds to 50%
of available power being delivered to the load. As noted in
Table 1, when Θ = 114°, only 25% of the available power
is being delivered to the load and the power drops quickly
as Θ approaches 180°.
With an average rectification scheme and the typical
calibration to compensate for errors with sine waves, the
RMS level of an input sine wave is properly reported; it is
only with a non-sinusoidal waveform that errors occur.
Because of this calibration, and the output reading in
V
an actual RMS-to-DC converter as opposed to a calibrated
average rectifier.
8
RMS
, the term True-RMS got coined to denote the use of
MAINS
AC
V
I
V
V
LOAD
LOAD
LINE
THY
U
V
LINE
+
–
Θ
Figure 2a
Figure 2b
+
CONTROL
U
V
I
LOAD
LOAD
–
W
1968 F02b
+
–
1968 F02a
V
THY
U
1
the lowpass filter. The input to the LPF is the calculation
from the multiplier/divider; (V
filter will take the average of this to create the output,
mathematically:
Unlike the prior generation RMS-to-DC converters, the
LTC1968 computation does NOT use log/antilog circuits,
which have all the same problems, and more, of log/
antilog multipliers/dividers, i.e., linearity is poor, the band-
width changes with the signal amplitude and the gain drifts
with temperature.
How the LTC1968 RMS-to-DC Converter Works
The LTC1968 uses a completely new topology for RMS-to-
DC conversion, in which a ∆Σ modulator acts as the
divider, and a simple polarity switch is used as the multi-
plier
Protected by multiple patents.
Because V
⎛
⎜
⎜
⎝
(
V
V
V
Figure 3. RMS-to-DC Converter with Implicit Computation
V
1
OUT
OUT
OUT
( )
V
OUT
V
as shown in Figure 4.
OUT
IN
=
=
=
)
2
2
⎛
⎜
⎜
⎝
⎞
⎟
⎟
⎠
⎛
⎝
V
=
( )
( )
IN
( )
=
V
V
V
V
OUT
V
( )
OUT
OUT
IN
IN
IN
V
⎛
⎝
IN
( )
V
2
V
2
2
is DC,
OUT
IN
⎞
⎠
⎞
⎟
⎟
⎠
2
=
,
,
,
×
or
2
and
RMS V
⎞
⎠
÷
,
so
( )
IN
( )
V
V
OUT
IN
LPF
IN
2
)
2
/V
OUT
1968 F03
. The lowpass
V
OUT
1968f