MAX1865TEEP+ Maxim Integrated Products, MAX1865TEEP+ Datasheet - Page 17
![IC PWR SUPPLY CONTROLLER 20QSOP](/photos/6/61/66144/20-qsop_21-0055_sml.jpg)
MAX1865TEEP+
Manufacturer Part Number
MAX1865TEEP+
Description
IC PWR SUPPLY CONTROLLER 20QSOP
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX1864TEEE.pdf
(25 pages)
Specifications of MAX1865TEEP+
Applications
Power Supply Controller
Voltage - Input
4.5 ~ 28 V
Current - Supply
1.4mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
20-QSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Supply
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
The key selection parameters for the output capacitor
are the actual capacitance value, the equivalent series
resistance (ESR), and voltage-rating requirements,
which affect the overall stability, output ripple voltage,
and transient response.
The output ripple has two components: variations in the
charge stored in the output capacitor, and the voltage
drop across the capacitor’s ESR caused by the current
into and out of the capacitor:
The output voltage ripple as a consequence of the ESR
and output capacitance is:
where I
Inductor Value section). These equations are suitable
for initial capacitor selection, but final values should be
set by testing a prototype or evaluation circuit. As a
general rule, a smaller ripple current results in less out-
put ripple. Since the inductor ripple current is a factor
of the inductor value and input voltage, the output volt-
age ripple decreases with larger inductance but
increases with lower input voltages.
Figure 5. Reducing the Switching EMI
P-P
MAX1864
MAX1865
V
TO VL
RIPPLE
xDSL/Cable Modem Triple/Quintuple Output
is the peak-to-peak inductor current (see
I
V
V
P P
RIPPLE ESR
RIPPLE C
−
=
=
______________________________________________________________________________________
GND
V
BST
⎛
⎜
⎝
DH
DH
(
( )
RIPPLE ESR
LX
V
IN
ƒ
=
)
-
SW
V
2
=
(OPTIONAL)
(OPTIONAL)
(
OUT
C
C
L
I
BST
R
R
P P
OUT SW
GATE
GATE
I
−
P P
)
⎞
⎟
⎠
−
ESR
⎛
⎜
⎝
+
ƒ
V
V
OUT
V
IN
RIPPLE C
Output Capacitor
⎞
⎟
⎠
N
N
H
L
( )
L
With low-cost aluminum electrolytic capacitors, the
ESR-induced ripple can be larger than that caused by
the current into and out of the capacitor. Consequently,
high-quality low-ESR aluminum-electrolytic, tantalum,
polymer, or ceramic filter capacitors are required to
minimize output ripple. Best results at reasonable cost
are typically achieved with an aluminum-electrolytic
capacitor in the 470µF range, in parallel with a 0.1µF
ceramic capacitor.
Since the MAX1864/MAX1865 use a current-mode con-
trol scheme, the output capacitor forms a pole that
affects circuit stability (see Compensation Design).
Furthermore, the output capacitor’s ESR also forms a
zero.
The MAX1864/MAX1865s’ response to a load transient
depends on the selected output capacitor. After a load
transient, the output instantly changes by ESR
ΔI
will sag further, depending on the inductor and output
capacitor values.
After a short period of time (see Typical Operating
Characteristics), the controller responds by regulating
the output voltage back to its nominal state. For appli-
cations that have strict transient requirements, low-ESR
high-capacitance electrolytic capacitors are recom-
mended to minimize the transient voltage swing.
Do not exceed the capacitor’s voltage or ripple-current
ratings.
The MAX1864/MAX1865 controllers use an internal
transconductance error amplifier whose output com-
pensates the control loop. Connect a series resistor
and capacitor between COMP and GND to form a pole-
zero pair. The external inductor, high-side MOSFET,
output capacitor, compensation resistor, and compen-
sation capacitor determine the loop stability. The induc-
tor and output capacitor are chosen based on
performance, size, and cost. Additionally, the compen-
sation resistor and capacitor are selected to optimize
control-loop stability. The component values shown in
the standard application circuits (Figures 1 and 6) yield
stable operation over a broad range of input-to-output
voltages.
The controller uses a current-mode control scheme that
regulates the output voltage by forcing the required
current through the external inductor, so the
MAX1864/MAX1865 use the voltage across the high-
side MOSFET’s R
Using the current-sense amplifier’s output signal and
the amplified feedback voltage, the control loop deter-
mines the peak inductor current by:
LOAD
. Before the controller can respond, the output
DS(ON)
Power Supplies
to sense the inductor current.
Compensation Design
17
✕