ISL6443IRZ Intersil, ISL6443IRZ Datasheet - Page 11
![IC CTRLR SGL/STEP DOWN PWM 28QFN](/photos/7/48/74846/isl6443irz_sml.jpg)
ISL6443IRZ
Manufacturer Part Number
ISL6443IRZ
Description
IC CTRLR SGL/STEP DOWN PWM 28QFN
Manufacturer
Intersil
Datasheet
1.ISL6443IRZ.pdf
(18 pages)
Specifications of ISL6443IRZ
Applications
Power Supplies
Current - Supply
50µA
Voltage - Supply
5.6 V ~ 24 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
28-QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL6443IRZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ISL6443IRZ-TK
Manufacturer:
INTERSIL
Quantity:
20 000
Functional Description
General Description
The ISL6443 integrates control circuits for two synchronous
buck converters and one linear controller. The two
synchronous bucks operate out of phase to substantially
reduce the input ripple and thus reduce the input filter
requirements. The chip has four control lines (SS1, SD1,
SS2, and SD2), which provide independent control for each
of the synchronous buck outputs.
The buck PWM controllers employ a free-running frequency
of 300kHz. The current mode control scheme with an input
voltage feed-forward ramp input to the modulator provides
excellent rejection of input voltage variations and provides
simplified loop compensations.
The linear controller can drive either a PNP or PFET to provide
ultra low-dropout regulation with programmable voltages.
Internal 5V Linear Regulator (VCC_5V)
All ISL6443 functions are internally powered from an on-
chip, low dropout 5V regulator. The maximum regulator input
voltage is 24V. Bypass the regulator’s output (VCC_5V) with
a 4.7µF capacitor to ground. The dropout voltage for this
LDO is typically 600mV, so when VCC_5V is greater than
5.6V, VCC_5V is typically 5V. The ISL6443 also employs an
undervoltage lockout circuit that disables both regulators
when VCC_5V falls below 4.4V.
The internal LDO can source over 60mA to supply the IC,
power the low side gate drivers, charge the external boot
capacitor and supply small external loads. When driving
large FETs especially at 300kHz frequency, little or no
regulator current may be available for external loads.
For example, a single large FET with 15nC total gate charge
requires 15nC x 300kHz = 4.5mA. Also, at higher input
voltages with larger FETs, the power dissipation across the
internal 5V will increase. Excessive dissipation across this
regulator must be avoided to prevent junction temperature
rise. Larger FETs can be used with 5V ±10% input
applications. The thermal overload protection circuit will be
triggered, if the VCC_5V output is short circuited. Connect
VCC_5V to V
Soft-Start Operation
When soft-start is initiated, the voltage on the SS pin of the
enabled PWM channels starts to ramp gradually, due to the
5μA current sourced into the external capacitor. The output
voltage follows the soft-start voltage.
When the SS pin voltage reaches 0.8V, the output voltage of
the enabled PWM channel reaches the regulation point, and
the soft-start pin voltage continues to rise. At this point the
PGOOD and fault circuitry is enabled. This completes the
soft-start sequence. Any further rise of SS pin voltage does
not affect the output voltage. By varying the values of the
soft-start capacitors, it is possible to provide sequencing of the
IN
for 5V ±10% input applications.
11
ISL6443
main outputs at start-up. The soft-start time can be obtained
from the following equation:
T
The soft-start capacitors can be chosen to provide startup
tracking for the two PWM outputs. This can be achieved by
choosing the soft-start capacitors such that the soft-start
capacitor ration equals the respective PWM output voltage
ratio. For example, if I use PWM1 = 1.2V and PWM2 = 3.3V
then the soft-start capacitor ratio should be, C
1.2/3.3 = 0.364. Figure 14 shows that soft-start waveform
with C
Output Voltage Programming
A resistive divider from the output to ground sets the output
voltage of either PWM channel. The center point of the
divider shall be connected to FBx pin. The output voltage
value is determined by the following equation.
where R1 is the top resistor of the feedback divider network
and R2 is the resistor connected from FBx to ground.
V
SOFT
FIGURE 14. PWM1 AND PWM2 OUTPUT TRACKING DURING
OUTx
SS1
=
=
0.8V
0.8V
= 0.01µF and C
FIGURE 13. SOFT-START OPERATION
STARTUP
⎛
⎝
⎛
⎝
C
-----------
5μA
R1
--------------------- -
SS
SS1 1V/DIV
VCC_5V 1V/DIV
R2
V
+
⎞
⎠
OUT1
R2
⎞
⎠
1V/DIV
SS2
= 0.027µF.
V
V
OUT1
SS1
OUT2
/C
August 9, 2006
1V/DIV
1V/DIV
SS1
FN9044.2
=