MIC2562A-1BM TR Micrel Inc, MIC2562A-1BM TR Datasheet
MIC2562A-1BM TR
Specifications of MIC2562A-1BM TR
MIC2562A-1BMTR
Related parts for MIC2562A-1BM TR
MIC2562A-1BM TR Summary of contents
Page 1
... PC Card slot power supply pins, both The MIC2562A switches between the three V PP ages (0V, 3.3V and 5.0V) and the V 3.3V 12.0V) required by PC Cards. The MIC2562A switches voltages from the system power supply Output voltage is selected by two digital inputs each and PP ...
Page 2
... Ordering Information Part Number MIC2562A-0BM MIC2562A-1BM MIC2562A-0YM MIC2562A-1YM MIC2562A-1BTS MIC2562A-1YTS Note. 1. See “MIC2562A-0 Control Logic” table for a description of the differences between the logic options. Pin Configuration 14-Pin SOIC (M) Both V IN pins must be connected. CC5 All three V OUT pins must be connected. ...
Page 3
... MIC2562A Absolute Maximum Ratings Supply Voltage ............................................... +15V ................................................................... +7.5V CC3 V IN ................................................................... +7.5V CC5 FLAG Pull-up Voltage ................................................ +7.5V Logic Input Voltages ..................................... –0.3V to +10V Output Current (each output) V OUT ............................... >200mA, Internally Limited PP V OUT ..................................... >1A, Internally Limited CC Power Dissipation ( .......... Internally Limited D A SOIC ................................................................... 800mW Lead Temperature (5 sec ...
Page 4
... not required for operation must be either high impedance or greater than or approximately equal to the highest voltage V PP and 5V are connected to the MIC2562A, V 10. A 10k pull-up resistor is connected between FLAG and V June 2004 Condition (4) V OUT = 90% to 10% of 3.3V ...
Page 5
... PP OFF to 3.3V to 12V to 12V Figure 1. MIC2562A V Timing Diagram PP is disabled. At “E,” programmed to 5V. At “F,” set to 12V. And at “K,” 3. OFF Figure 2. MIC2562A V Timing Diagram CC is programmed to 5V. And at “D,” 12V OFF OFF 3.3V is selected. At “B,” set to 12V. At “G,” again disabled ...
Page 6
... MIC2562A MIC2562A-0 Control Logic Table V V CC5_EN CC3_EN MIC2562A-1 Control Logic Table V V CC5_EN CC3_EN June 2004 EN1 EN0 0 0 Clamped to Ground 0 1 Clamped to Ground 1 0 Clamped to Ground 1 1 Clamped to Ground (compatible with Cirrus Logic CL-PD6710 & PD672x-series Controllers PP_PGM PP_VCC ...
Page 7
... MIC2562A Logic Block Diagram EN1 EN0 V CC5_EN V CC3_EN /FLAG V CC3 IN V CC5 IN June 2004 MIC2562 Control Logic I LIMIT / Thermal Shutdown Gate Drive Generator 7 Micrel (optional OUT V CC OUT M9999-062204 ...
Page 8
... CC3 trolled to prevent damage to sensitive loads and meet all PC Card specification speed requirements. Supply Bypassing External capacitors are not required for operation. The MIC2562A is a switch and has no stability problems. For best results however, bypass V IN, V CC3 CC5 with 1 F capacitors to improve output ripple. As all internal ...
Page 9
... MIC2562A Figure 3. MIC2562A PC Card Slot Power Control Application with Dual V Figure 4. Typical MIC2562A PC Card Slot Power Control Application June 2004 5V System Power 3.3V Supply 12V CC3 IN V CC5 IN (opt) EN0 EN1 MIC2562 PCMCIA V CC5_EN Card Slot Controller V CC3_EN EN0 V PP OUT ...
Page 10
... System Power Supply PCMCIA Card Slot Controller Figure 5. PC Card Slot Power Control Application Without an Available 3.3V V Note and V IN are driven together. The MIC2562A is powered by the V CC3 CC5 V OUT will be 5V when either V CC CC3 of the V switch by using the V CC5 ...
Page 11
... MIC2562A Package Information 0.154 (3.90) 0.026 (0.65) MAX) 0.057 (1.45) 0.049 (1.25) June 2004 PIN 1 DIMENSIONS: INCHES (MM) 0.050 (1.27) 0.016 (0.40) TYP TYP 0.006 (0.15) 0.344 (8.75) 0.337 (8.55) SEATING PLANE 14-Pin Narrow SOIC (M) 16-Pin TSSOP (TS) 11 0.193 (4.90 –6 0.244 (6.20) ...
Page 12
... MIC2562A MICREL, INC. 1849 FORTUNE DRIVE SAN JOSE, CA 95131 USA + 1 (408) 944-0800 TEL The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. ...