MIC2043-2BTS TR Micrel Inc, MIC2043-2BTS TR Datasheet - Page 11
![IC DISTRIBUTION SW SGL 14-TSSOP](/photos/28/19/281948/mic2549_14-tssop_sml.jpg)
MIC2043-2BTS TR
Manufacturer Part Number
MIC2043-2BTS TR
Description
IC DISTRIBUTION SW SGL 14-TSSOP
Manufacturer
Micrel Inc
Type
High Side Switchr
Datasheet
1.MIC2042-1YM.pdf
(15 pages)
Specifications of MIC2043-2BTS TR
Number Of Outputs
1
Rds (on)
60 mOhm
Internal Switch(s)
Yes
Current Limit
Adjustable
Voltage - Input
0.8 ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
14-TSSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
MIC2043-2BTSTR
MIC2043-2BTSTR
MIC2043-2BTSTR
January 2005
Functional Description
The MIC2042 and MIC2043 are high-side N-Channel switches
equipped with programmable current limit up to 3A for use in
general purpose power distribution applications. The switches,
available with active-high or active-low enable inputs, provide
output slew-rate control and circuit protection via thermal
shutdown and an optional output latch during overcurrent
conditions.
Input and Output
V
must be present for the switch to operate. V
the drain of the output MOSFET and sources power to the
switched load. V
is the source terminal of the output MOSFET and attaches to
the load. In a typical circuit, current flows from V
toward the load. If V
from V
device is enabled. When disabled (OFF), the switch will block
current flow from either direction.
Enable Input
Enable, the ON/OFF control for the output switch, is a digital
input available as an active-high (–1) or active-low (–2)
signal. The EN pin, referenced to approximately 0.5 × VBIAS,
must be driven to a clearly defined logic high or logic low.
Failure to observe this requirement, or allowing EN to float,
will cause the MIC2042/43 to exhibit unpredictable behavior.
EN should not be allowed to go negative with respect to
ground, nor allowed to exceed VBIAS. Failure to adhere to
these conditions may result in damage to the device.
Undervoltage Lockout
When the switch is enabled, undervoltage lockout (UVLO)
monitors the input voltage, V
MOSFET from turning on until V
level, nominally set at 1.45V. The UVLO threshold is adjust-
able and can be varied by applying an external resistor divider
to the UVLOIN pin from VIN to GND. The resistive divider
network is required when the input voltage is below 1.5V. The
UVLO threshold is internally preset to 1.45V if the UVLOIN
pin is left open. See “Applications Information” section.
MIC2042/2043
BIAS
supplies power to the internal circuitry of the switch and
OUT
3.5
2.5
1.5
0.5
4
3
2
1
0
0 120 240 360 480 600 720 840 960
CLF (LO)
to V
Current Limit
IN
vs. R
IN
since the switch is bi-directional when the
R
CLF (HI)
must be less than or equal to V
SET
OUT
–40°C to +85°C
V
SET
IN
(Ω)
= V
is greater than V
BIAS
= 5V
IN
IN
, and prevents the output
exceeds a predetermined
IN
IN
, current will flow
is connected to
Figure 3. Current Limit Factor
3.5
2.5
1.5
0.5
BIAS
IN
4
3
2
1
0
0 120 240 360 480 600 720 840 960
to V
CLF (LO)
. V
Current Limit
OUT
OUT
vs. R
CLF (HI)
R
11
SET
–40°C to +85°C
V
SET
IN
(Ω)
Programmable Current Limit
The MIC2042/43 is designed to prevent damage to the
external load by limiting the maximum amount of current it
can draw. The current limit is programmed by an external
resistor (R
active when the output voltage is at least 200mV below the
voltage at the input to the device. The limiting current value
is defined by the current limit factor (CLF) divided by R
and the MIC2042/43 will limit from 0.5A to 3A with a set point
accuracy of ±22%. In programming the nominal current limit,
the value of R
And given the ±22% tolerance of the current limit factor (CLF),
the external resistor is bound by:
The graphs below (Figure 3) display the current limit factor
characteristic over the full temperature range at the indicated
voltage. These curves can be used as a point of reference in
determining the maximum variation in the device’s current
limit over the full temperature range. For example: With
V
(R
MIC2042/43 would be 1.66A and 2.34A, respectively, as
shown on the 3V graph using the 192Ω reference point.
When current limiting occurs, the MIC2042 and MIC2043
respond differently. Upon first reaching the limiting current
both devices restrict current flow, allowing the load voltage to
drop below V
ceeds 200mV, then a fault condition is declared and the fault
delay timer is started. If the fault condition persists longer than
the delay period, typically 28ms, then the /FAULT output
asserts low. At this point, the MIC2042 will continue to supply
current to the load at the limiting value (I
MIC2043 will latch off its output.
= V
IN
BIAS
SET
= V
= 3V
103Ω ≤ R
R
= 192Ω), the low and high current limit settings for the
SET
BIAS
SET
=
SET
IN
) connected from ILIM to ground and becomes
I
LIMIT
CLF
= 3.0V and a nominal 2A current limit
. If the VIN-to-VOUT differential voltage ex-
SET
is determined using the following equation:
≤ 970Ω
=
(
390A
3.5
2.5
1.5
0.5
I
LIMIT
4
3
2
1
0
0 120 240 360 480 600 720 840 960
CLF (LO)
× Ω
Current Limit
)
vs. R
CLF (HI)
R
–40°C to +85°C
V
SET
IN
SET
= V
(Ω)
LIMIT
BIAS
= 1.6V
), whereas the
M0512-112603
Micrel
SET
(1)
(2)
,