MIC2043-1BTS TR Micrel Inc, MIC2043-1BTS TR Datasheet - Page 14
![IC DISTRIBUTION SW SGL 14-TSSOP](/photos/28/19/281948/mic2549_14-tssop_sml.jpg)
MIC2043-1BTS TR
Manufacturer Part Number
MIC2043-1BTS TR
Description
IC DISTRIBUTION SW SGL 14-TSSOP
Manufacturer
Micrel Inc
Type
High Side Switchr
Datasheet
1.MIC2042-1YM.pdf
(15 pages)
Specifications of MIC2043-1BTS TR
Number Of Outputs
1
Rds (on)
60 mOhm
Internal Switch(s)
Yes
Current Limit
Adjustable
Voltage - Input
0.8 ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
14-TSSOP
Short Circuit Current Limit
0.5 to 3A
Input Voltage Range
0.8 to 5.5V
Number Of Switches
Single
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
14
Package Type
TSSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
MIC2043-1BTSTR
MIC2043-1BTSTR
MIC2043-1BTSTR
MIC2042/2043
M0512-112603
Power Dissipation
Power dissipation depends on several factors such as the
load, PCB layout, ambient temperature, and package type.
The following equations can be used to calculate power
dissipation and die temperature.
Calculation of power dissipation can be accomplished by the
following equation:
To relate this to junction temperature, the following equation
can be used:
where T
and Rθ
Printed Circuit Board Hot-Plug
The MIC2042/43 are ideal inrush current limiting power
switches suitable for hot-plug applications. Due to the inte-
grated charge pump, the MIC2042/43 present a high imped-
ance when in the off state and the device slowly becomes a
low impedance as it turns on. This effectively isolates power
supplies from highly capacitive loads by reducing inrush
current during hot-plug events. This same feature also can be
used for soft-start requirements.
PCB Layout Recommendations
The MIC2042 and MIC2043 have very low on-resistance,
typically 40mΩ, and the switches can provide up to 3A of
continuous output current. Under such heavy loads, the
power consumed by the devices may cause the devices to
P
T
J
D
JA
J
= P
= R
= junction temperature, T
is the thermal resistance of the package.
D
DS(ON)
× Rθ
JA
× (I
m
+ T
OUT
A
)
2
W
W
A
W
= ambient temperature
m
Figure 4. Lower UVLO Setting
m
W
(5)
(6)
MIC2042-1BTS
14
heat up considerably. The following list contains some useful
suggestions for PCB layout design of the MIC2042/43 in
order to prevent the die from overheating under normal
operating conditions:
1. Supply additional copper area under the device
2. Provide additional pad area on the corner pins of
3. Tie the common power pins (VIN = pins 8 and
4. For PCB trace width calculation, there are
to remove heat away from the IC.
See “Application Hint 17” for a general guideline
in calculating the suggested area.
the MIC2042/43 IC for heat distribution.
12 and VOUT = pins 10, 11, 14 for the 14-pin
TSSOP, VIN = pins 5 and 7 and VOUT = pins 6
and 8 for the 8-pin SOP) together in a manner
such that the traces entering and leaving the
device have a uniform width sufficient for the
application’s current requirements plus added
margin (25% minimum recommended).
Ex: For 2A maximum current, design traces for
2.5A capability.
numerous calculator programs available on the
internet and elsewhere. As a general rule of
thumb, 15-20 mils for every 1A of current when
using 1oz. copper. However, the trace width
calculators often take into account maximum
temperature increase constraints, as well as
layer arrangement, in determining the PCB trace
widths.
W
W
W
W
m
January 2005
Micrel