MC33035DW ON Semiconductor, MC33035DW Datasheet - Page 25
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
MC33035DW
Manufacturer Part Number
MC33035DW
Description
IC CTRLR DC MOTOR BRSHLSS 24SOIC
Manufacturer
ON Semiconductor
Type
Brushless DC Motor Controllerr
Datasheet
1.NCV33035DWR2G.pdf
(28 pages)
Specifications of MC33035DW
Applications
DC Motor Controller, Brushless (BLDC)
Number Of Outputs
1
Current - Output
100mA
Voltage - Load
5.9 V ~ 6.5 V
Voltage - Supply
10 V ~ 30 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
24-SOIC (7.5mm Width)
Operating Supply Voltage
10 V to 30 V
Supply Current
20 mA
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MC33035DW
Manufacturer:
MOTO
Quantity:
5 510
Part Number:
MC33035DW
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Part Number:
MC33035DW.
Manufacturer:
ON/安森美
Quantity:
20 000
Company:
Part Number:
MC33035DWG
Manufacturer:
FREESCALE
Quantity:
1 500
Company:
Part Number:
MC33035DWG
Manufacturer:
ON Semiconductor
Quantity:
1 285
Part Number:
MC33035DWG
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
MC33035DWR2
Manufacturer:
DHA
Quantity:
20 000
Company:
Part Number:
MC33035DWR2G
Manufacturer:
FREESCALE
Quantity:
1 500
Part Number:
MC33035DWR2G
Manufacturer:
ON/安森美
Quantity:
20 000
Brush Motor Control
DC motors, it may also be used to control DC brush type
motors. Figure 46 shows an application of the MC33035
driving a MOSFET H−bridge affording minimal parts count
to operate a brush−type motor. Key to the operation is the
input sensor code [100] which produces a top−left (Q
a
forward/reverse pin is at logic [1]; top−right (Q
(Q
logic [0]. This code supports the requirements necessary for
H−bridge drive accomplishing both direction and speed
control.
width modulated frequency of approximately 25 kHz.
Motor speed is controlled by adjusting the voltage presented
to the noninverting input of the error amplifier establishing
the PWM’s slice or reference level. Cycle−by−cycle current
limiting of the motor current is accomplished by sensing the
voltage (100 mV) across the R
H−bridge motor current. The over current sense circuit
Though the MC33035 was designed to control brushless
The controller functions in a normal manner with a pulse
2
) drive is realized when the Forward/Reverse pin is at
bottom−right
(Q
3
)
drive
S
resistor to ground of the
when
the
4
), bottom−left
controller’s
MC33035, NCV33035
http://onsemi.com
1
) and
25
makes it possible to reverse the direction of the motor, using
the normal forward/reverse switch, on the fly and not have
to completely stop before reversing.
LAYOUT CONSIDERATIONS
control circuits on wire−wrap or plug−in prototype
boards. High frequency printed circuit layout techniques
are imperative to prevent pulse jitter. This is usually caused
by excessive noise pick−up imposed on the current sense or
error amp inputs. The printed circuit layout should contain
a ground plane with low current signal and high drive and
output buffer grounds returning on separate paths back to the
power supply input filter capacitor V
capacitors (0.1 μF) connected close to the integrated circuit
at V
be required depending upon circuit layout. This provides a
low impedance path for filtering any high frequency noise.
All high current loops should be kept as short as possible
using heavy copper runs to minimize radiated EMI.
Do not attempt to construct any of the brushless motor
CC
, V
C
, V
ref
and the error amp noninverting input may
M
. Ceramic bypass