IPS0151 International Rectifier, IPS0151 Datasheet
![IC MOSFET PWR SWITCH TO-220AB](/photos/5/40/54079/to-220ab_sml.jpg)
IPS0151
Specifications of IPS0151
Q827406
Available stocks
Related parts for IPS0151
IPS0151 Summary of contents
Page 1
... Active clamp Low current & logic level input E.S.D protection Description The IPS0151/IPS0151S are fully protected three terminal SMART POWER MOSFETs that feature over-current, over-temperature, ESD protection and drain to source active clamp.These devices combine a HEXFET POWER MOSFET and a gate driver. They offer full protection and high reliability required in harsh envi- ronments ...
Page 2
... C/W IPS0151S I sd Diode max. pulsed current pulsed P d Maximum power dissipation o (rth=62 C/W) IPS0151 o (rth=80 C/W) IPS0151S ESD1 Electrostatic discharge voltage ESD2 Electrostatic discharge voltage T stor. Max. storage temperature T j max. Max. junction temperature T lead Lead temperature (soldering, 10 seconds) Thermal Characteristics ...
Page 3
... Min. Typ. Max. Units Test Conditions — 165 — 1.5 2 — 400 — IPS0151( 5V 14V 40V 20mA (see Fig.3 & shutdown (see Fig.3 & 50mA 14V over-current triggered See figure See figure 2 2 ...
Page 4
... IPS0151(S) Functional Block Diagram All values are typical IN 8 Lead Assignments 2 ( TO-220 IPS0151 4 200 Part Number DRAIN 47 V 200 k I sense T > 165°c I > Isd SOURCE 2 ( PAK (SMD220) IPS0151S www.irf.com ...
Page 5
... Appl . Notes to evaluate power dissipation ) Figure 3 - Active clamp waveforms www.irf.com 90 % Vin 10 % Tr-in Tr-in t > T reset 90 % Ids Vds Figure rise time & switching time definitions T clamp Rem : V load is negative during demagnetization Figure 4 - Active clamp test circuit IPS0151(S) Td off load + Vin IN Vds S Ids 5 ...
Page 6
... IPS0151(S) All curves are typical values with standard footprints. Operating in the shaded area is not recommended Figure 5 - Rds Input Voltage (V) 8 ton delay 7 rise tim e 6 130% final 5 rdson Figure 7 - Turn-ON Delay Time, Rise Time & Time to 130% final R ds(on) (us) Vs Input Voltage (V) ...
Page 7
... Figure 9 - Turn-ON Delay Time, Rise Time & Time to 130% final Rds (on) (us Resistor ( ) Isd 25° Ilim 25° Figure 11 - Current Iim. & Ishutdown (A) Vs Vin (V) www.irf.com 10000 Figure 10 - Turn-OFF Delay Time & Fall Time (us -50 -25 Figure 12 - Ishutdown (A) Vs Temperature ( IPS0151(S) delay off fall tim Resistor ( ) 100 125 150 ...
Page 8
... Load characteristic should be below this curve 200 1 Figure 14 - Max.Cont. Ids (A) Vs Ambient Figure 16 - Transient Thermal Imped Time (s) - IPS0151/IPS051S Current path capability should be above this T=25°C T=100°C o Temperature ( C) Single pulse rth free air TO220 footprint SMD220 rth junction to case = 1.8°C/W ...
Page 9
... Figure 19 - Turn-on, Turn-off, and Treset ( Tjunction ( C) www.irf.com 120% 115% 110% 105% 100% 95% 90% 85% 80% 100 125 150 -50 -25 Figure 18 - Vin clamp and V clamp2 ( IPS0151(S) Vds clam p @ Isd Vin clam p @ 10m 100 125 150 o Vs Tjunction ( C) 9 ...
Page 10
... IPS0151(S) Case Outline NOTES: 3-Lead TO-220AB 01-6024 00 IRGB 01-3026 01 (TO-220AB) www.irf.com ...
Page 11
... Case Outline www.irf.com 3-Lead D 2 PAK IPS0151(S) 01-6022 00 115-0088 10 (TO-263AB) 11 ...
Page 12
... IPS0151(S) 2 Tape & Reel - D PAK (SMD220) IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 12 Data and specifications subject to change without notice. 01-3072 00 11/13/2001 www.irf.com ...
Page 13
Note: For the most current drawings please refer to the IR website at: http://www.irf.com/package/ ...