MC33153PG ON Semiconductor, MC33153PG Datasheet - Page 11

• Manufacturer Part Number: MC33153PG
• Description: IC DRIVER GATE SINGLE IGBT 8DIP
• Manufacturer: ON Semiconductor
• Type: Single IGBT Gate Driverr

Specifications of MC33153PG

• Configuration: Low-Side
• Input Type: Non-Inverting
• Delay Time: 80ns
• Current - Peak: 1A
• Number Of Configurations: 1
• Number Of Outputs: 1
• Voltage - Supply: 11 V ~ 20 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Supply Current: 20 mA
• Mounting Style: Through Hole
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• High Side Voltage - Max (bootstrap): -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: MC33153PGOS

driven from an optoisolator, an input pull up resistor is
required. This resistor value should be set to bias the output
transistor at the desired current. A decoupling capacitor
should be placed close to the IC to minimize switching noise.
protection features are not required, then both the Fault
Blanking/Desaturation and Current Sense Inputs should
both be connected to the Kelvin Ground (Pin 2). When used
with a single supply, the Kelvin Ground and V
be connected together. Separate gate resistors are
recommended to optimize the turn−on and turn−off drive.
Kelvin Ground should be connected to the emitter of the
IGBT. If the protection features are not used, then both the
Fault Blanking/Desaturation and the Current Sense Inputs
should be connected to Ground. The input optoisolator
should always be referenced to V
is connected to the Fault Blanking/Desaturation pin. The
Figure 35 shows a basic IGBT driver application. When
A bootstrap diode may be used for a floating supply. If the
When used in a dual supply application as in Figure 36, the
If desaturation protection is desired, a high voltage diode
Figure 36. Dual Supply Application
Figure 35. Basic Application
18 V
-5.0 V
15 V
7
4
7
4
Fault
Input
Fault
Input
MC33153
MC33153
V
V
CC
EE
V
V
6
3
CC
EE
6
3
EE
Output
Desat/
Sense
Blank
GND
Output
Desat/
Sense
Bootstrap
.
Blank
GND
8
5
1
2
8
5
1
2
APPLICATION INFORMATION
EE
pins should
http://onsemi.com
B+
11
blanking capacitor should be connected from the
Desaturation pin to the V
blanking capacitor should be connected to the Kelvin
Ground. The Current Sense Input should be tied high
because the two comparator outputs are ANDed together.
Although the reverse voltage on collector of the IGBT is
clamped to the emitter by the free−wheeling diode, there is
normally considerable inductance within the package itself.
A small resistor in series with the diode can be used to
protect the IC from reverse voltage transients.
voltage is applied to the Current Sense Input. The sense trip
voltages are referenced to the Kelvin Ground pin. The sense
voltage is very small, typically about 65 mV, and sensitive
to noise. Therefore, the sense and ground return conductors
should be routed as a differential pair. An RC filter is useful
in filtering any high frequency noise. A blanking capacitor
is connected from the blanking pin to V
capacitance on the blanking pin provides a very small level
of blanking if left open. The blanking pin should not be
grounded when using current sensing, that would disable the
sense. The blanking pin should never be tied high, that
would short out the clamp transistor.
When using sense IGBTs or a sense resistor, the sense
Figure 37. Desaturation Application
Figure 38. Sense IGBT Application
18 V
18 V
7
4
7
4
EE
Fault
Input
Fault
Input
pin. If a dual supply is used, the
MC33153
MC33153
V
V
V
CC
V
EE
6
3
CC
EE
6
3
Output
Desat/
Sense
Blank
Output
Desat/
GND
Sense
Blank
GND
8
5
1
2
8
5
1
2
EE
C
Blank
. The stray