IRS2332DSTRPBF International Rectifier, IRS2332DSTRPBF Datasheet
IRS2332DSTRPBF
Specifications of IRS2332DSTRPBF
Related parts for IRS2332DSTRPBF
IRS2332DSTRPBF Summary of contents
Page 1
Features • Floating channel designed for bootstrap operation Fully operational to +600 V • Tolerant to negative transient voltage – dV/dt immune • Gate drive supply range from • Undervoltage lockout for all channels • ...
Page 2
... Machine Model IC Latch-Up Test RoHS Compliant † Qualification standards can be found at International Rectifier’s web site †† Higher qualification ratings may be available should the user have such requirements. Please contact your International Rectifier sales representative for further information. ††† ...
Page 3
Absolute Maximum Ratings Absolute Maximum Ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to V measured under board mounted and still air conditions. Symbol V High Side Floating Supply ...
Page 4
Recommended Operating Conditions The Input/Output logic timing diagram is shown in figure 1. For proper operation the device should be used within the recommended conditions. All voltage parameters are absolute voltage referenced to V tested with all supplies biased at ...
Page 5
Dynamic Electrical Characteristics BIAS CC BS1,2,3 SO1,2,3 Symbol Definition SR+ Operational Amplifier Slew Rate (+) SR- Operational Amplifier Slew Rate (-) www.irf.com , C = 1000 pF ...
Page 6
Static Electrical Characteristics BIAS CC BS1,2,3 SO1,2,3 are referenced to V and are applicable to all six logic input leads: HIN1,2,3 & LIN1,2,3. The V SS are referenced to ...
Page 7
Static Electrical Characteristics- Continued BIAS CC BS1,2,3 SO1,2,3 are referenced to V and are applicable to all six logic input leads: HIN1,2,3 & LIN1,2,3. The V SS are referenced ...
Page 8
Lead Definitions Symbol HIN1,2,3 Logic input for high side gate driver outputs (HO1,2,3), out of phase LIN1,2,3 Logic input for low side gate driver output (LO1,2,3), out of phase FAULT Indicates over-current or undervoltage lockout (low side) has occurred, negative ...
Page 9
Application Information and Additional Details Information regarding the following topics are included as subsections within this section of the datasheet. • IGBT/MOSFET Gate Drive • Switching and Timing Relationships • Deadtime • Matched Propagation Delays • Input Logic Compatibility • ...
Page 10
Switching and Timing Relationships The relationship between the input and output signals of the IRS233(0,2)(D) are illustrated below in Figures 3. From these figures, we can see the definitions of several timing parameters (i.e., PW device. The following two figures ...
Page 11
Deadtime This family of HVICs features integrated deadtime protection circuitry. The deadtime for these ICs is fixed; other ICs within IR’s HVIC portfolio feature programmable deadtime for greater design flexibility. The deadtime feature inserts a time period (a minimum deadtime) ...
Page 12
Matched Propagation Delays The IRS233(0,2)(D) family of HVICs is designed with propagation delay matching circuitry. response at the output to a signal at the input requires approximately the same time duration (i.e., t side channels and the high-side channels. Additionally, ...
Page 13
Shoot-Through Protection The IRS233(0,2)(D) family of high-voltage ICs is equipped with shoot-through protection circuitry (also known as cross- conduction prevention circuitry). Figure 8 shows how this protection circuitry prevents both the high- and low-side switches from conducting at the same ...
Page 14
Fault Reporting The IRS233(0,2)(D) family provides an integrated fault reporting output. There are two situations that would cause the HVIC to report a fault via the FAULT pin. The first is an undervoltage condition fault. Once the ...
Page 15
Figure 10: Programming over-temperature protection Truth Table: Undervoltage lockout and ITRIP Table 2 provides the truth table for the IRS233(0,2)(D). The first line shows that the UVLO for V FAULT output has gone low and the gate drive outputs have ...
Page 16
Figure 12: Typical input filter Short-Pulse / Noise Rejection This device’s input filter provides protection against short-pulses (e.g., noise) on the input lines. If the duration of the input signal is less than t , the output will not change ...
Page 17
Figure 16: Difference between the input pulse and the output pulse Integrated Bootstrap Functionality The new IRS233(0,2)D family features integrated high-voltage bootstrap MOSFETs that eliminate the need of the external bootstrap diodes and resistors in many applications. There is one ...
Page 18
Figure 17: Internal bootstrap MOSFET connection A bootstrap MOSFET is suitable for most of the PWM modulation schemes and can be used either in parallel with the external bootstrap network (i.e., diode and resistor replacement of it. ...
Page 19
Negative V Transient SOA S A common problem in today’s high-power switching converters is the transient response of the switch node’s voltage as the power switches transition on and off quickly while carrying a large current. A typical 3-phase inverter ...
Page 20
DC+ BUS OFF DC- BUS Figure 21: Q1 conducting Also when the V phase current flows from the inductive load back to the inverter (see Figures 23 and 24), and Q4 IGBT ...
Page 21
... International Rectifier’s HVICs have been designed for the robustness required in many of today’s demanding applications. An indication of the IRS233(0,2)(D)’s robustness can be seen in Figure 28, where there is represented the IRS233(0,2)(D) Safe ...
Page 22
DC- bus Current Sensing A ground referenced current signal amplifier has been included so that the current in the return leg of the DC bus may be monitored. A typical circuit configuration is provided in Fig.29. The signal coming from ...
Page 23
Figure 32: Operational Amplifier Common mode rejection measurement PCB Layout Tips Distance between high and low voltage components: It’s strongly recommended to place the components tied to the floating voltage pins (V and V ) near the respective high voltage ...
Page 24
Supply Capacitor recommended to place a bypass capacitor (C shown in Figure 35. A ceramic 1 μF ceramic capacitor is suitable for most applications. This component should be placed as close as possible to the pins in order ...
Page 25
Parameter Temperature Trends Figures 38-76 provide information on the experimental performance of the IRS233(0,2)(D)(S&J) HVIC. The line plotted in each figure is generated from actual lab data. A small number of individual samples were tested at three temperatures (-40 ºC, ...
Page 26
Exp -50 - Temperature ( Fig. 42. Turn-on Rise Time vs. Temperature 1000 900 800 Exp. 700 600 500 400 300 200 100 0 -50 -25 ...
Page 27
Exp -50 - Temperature ( Fig. 48. Operational Amplifier Slew Rate (+) vs. Temperature 2.5 2.0 Exp. 1.5 1.0 0.5 0.0 -50 - Temperature ( Fig. ...
Page 28
Exp. 100 50 0 -50 - Temperature ( Fig. 54. Low Level Output Voltage vs. Temperature Exp -50 - Temperature ...
Page 29
Exp. 8.4 8.2 8.0 7.8 -50 - Temperature ( Fig. 60. V Supply Undervoltage Negative CC Going Threshold vs. Temperature 9.0 8.5 8.0 Exp. 7.5 7.0 6.5 6.0 -50 -25 0 ...
Page 30
Exp. 606 506 406 306 206 106 6 -50 - Temperature ( Fig. 66. Output Low Short Circuit Pulsed Current vs. Temperature 200 180 160 140 120 100 Exp -50 -25 ...
Page 31
Exp -50 - Temperature ( Fig. 72. Operational Amplifier Output Sink Current vs. Temperature 0 -50 - -10 Exp. -12 -14 -16 ...
Page 32
Case Outlines www.irf.com IRS233(0,2)(D)(S&J)PbF 32 ...
Page 33
Case Outlines www.irf.com IRS233(0,2)(D)(S&J)PbF 33 ...
Page 34
Tape and Reel Details: SOIC28W F NOTE : CONTROLLING DIM ENSION CARRIER TAPE DIMENSION FOR 28SOICW Code REEL DIMENSIONS FOR 28SOICW Code ...
Page 35
Tape and Reel Details: PLCC44 F CARRIER TAPE DIMENSION FOR 44PLCC Code www.irf.com LOADED TAPE FEED DIRECTION NOTE : CONTROLLING E DIM ENSION Metric Imperial ...
Page 36
... The information provided in this document is believed to be accurate and reliable. However, International Rectifier assumes no responsibility for the consequences of the use of this information. International Rectifier assumes no responsibility for any infringement of patents or of other rights of third parties which may result from the use of this information. No license is granted by implication or otherwise under any patent or patent rights of International Rectifier. The specifications mentioned in this document are subject to change without notice. This document For technical support, please contact IR’ ...