TC4431COA Microchip Technology, TC4431COA Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
TC4431COA
Manufacturer Part Number
TC4431COA
Description
IC MOSFET DRIVER 30V 1.5A 8-SOIC
Manufacturer
Microchip Technology
Type
Microcontrollerr
Specifications of TC4431COA
Configuration
High-Side
Input Type
Inverting
Delay Time
62ns
Current - Peak
1.5A
Number Of Configurations
1
Number Of Outputs
1
Voltage - Supply
4.5 V ~ 30 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Device Type
High Side
Module Configuration
High Side
Peak Output Current
1.5A
Output Resistance
7ohm
Input Delay
62ns
Output Delay
78ns
Supply Voltage Range
4.5V To 30V
Driver Case
RoHS Compliant
Rise Time
40 ns
Fall Time
50 ns
Supply Voltage (min)
4.5 V
Supply Current
4 mA
Maximum Power Dissipation
470 mW
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
0 C
Number Of Drivers
1
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
High Side Voltage - Max (bootstrap)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
TC4431C0A
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TC4431COA
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
TC4431COA713
Manufacturer:
MICROCHIP
Quantity:
12 000
TC4431/TC4432
3.0
The descriptions of the pins are listed in
TABLE 3-1:
3.1
The V
driver and is rated for 4.5V to 30V with respect to the
ground pins. The V
ground with a local ceramic capacitor. The value of this
capacitor should be chosen based on the capacitive
load that is being driven.
3.2
The MOSFET driver input is a TTL/CMOS compatible
input with 250 mV of hysteresis between the high and
low threshold voltages. If an input signal level of greater
than 12V is applied to the device, a series current
limiting resistor is recommended.
3.3
The lockout pin enables/disables the undervoltage
lockout feature of the device. If undervoltage lockout is
desired (output is not enabled until the bias voltage
reaches 8.4V (typical) on the rising edge and is
disabled when the bias voltage reaches 7.7V (typical)
on the falling edge), the lockout pin should be left float-
ing. If operation below 7V is desired, the lockout pin
should be tied to ground.
DS21424D-page 6
Pin No.
DD
1
2
3
4
5
6
7
8
PIN DESCRIPTIONS
Supply Input (V
Control Input (IN)
Lockout Disable (LOCK DIS)
input is the bias supply input for the MOSFET
PIN FUNCTION TABLE
LOCK DIS
DD
Symbol
OUT
OUT
GND
GND
V
V
IN
DD
DD
input should be bypassed to
DD
)
Supply Input, 4.5V to 30V
TTL/CMOS Compatible Input
Input Pin, Enable/Disable for UV Lockout
Ground
Ground
Drive Output, Pull Down
Drive Output, Pull Up
Supply Input, 4.5V to 30V
Table
3-1.
3.4
The ground pins are the return path for the bias current
and for the high peak currents which discharge the load
capacitor. Both ground pins should be used to ensure
proper operation. The ground pins should be tied into a
ground plane or have short traces to the bias supply
source return.
3.5
The TC4431/TC4432 devices have individual source
and sink output pins. This feature can be used to adjust
the rise and fall time independently by adding separate
charge and discharge resistors external to the device.
Pin 7 (source output) can source 3 A peak currents into
capacitive loads and pin 6 (sink output) can sink 1.5 A
peak currents from a capacitive load.
Description
Ground (GND)
Drive Output (OUT)
© 2007 Microchip Technology Inc.