MAX16831ATJ+ Maxim Integrated Products, MAX16831ATJ+ Datasheet - Page 8

• Manufacturer Part Number: MAX16831ATJ+
• Description: IC LED DRIVR HIGH BRIGHT 32-TQFN
• Manufacturer: Maxim Integrated Products
• Type: HBLED Driverr

Specifications of MAX16831ATJ+

• Topology: PWM, Step-Down (Buck), Step-Up (Boost)
• Number Of Outputs: 1
• Internal Driver: No
• Type - Primary: Automotive
• Type - Secondary: High Brightness LED (HBLED), RGB
• Frequency: 125kHz ~ 600kHz
• Voltage - Supply: 5.5 V ~ 76 V
• Mounting Type: Surface Mount
• Package / Case: 32-TQFN Exposed Pad
• Operating Temperature: -40°C ~ 125°C
• Internal Switch(s): Yes
• Efficiency: 90%
• Low Level Output Current: 76 mA
• High Level Output Current: 67 mA
• Operating Supply Voltage: 5.5 V to 76 V
• Maximum Supply Current: 4.5 mA
• Maximum Power Dissipation: 2758 mW
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Current - Output / Channel: -
• Lead Free Status / Rohs Status: Details

High-Voltage, High-Power LED Driver with
Analog and PWM Dimming Control
8
8
9, 10, 11
16, 17
_______________________________________________________________________________________
_______________________________________________________________________________________
1, 24
PIN
12
13
14
15
18
19
20
21
22
23
2
3
4
5
6
7
8
CLKOUT
RTSYNC
NAME
AGND
COMP
QGND
SGND
UVEN
REG1
SNS+
SNS-
DGT
N.C.
DRV
REF
DIM
DRI
I.C.
OV
CS
FB
No Connection. Not internally connected.
Undervoltage Lockout (UVLO) Threshold/Enable Input. UVEN is a dual-function adjustable UVLO
threshold input with an enable feature. Connect UVEN to V
program the UVLO threshold. Connect UVEN directly to V
threshold. Apply a voltage greater than 1.244V to UVEN to enable the device.
5V Regulator Output. REG1 is an internal low-dropout voltage regulator that generates a 5V (V
6V) output voltage and supplies power to internal circuitry. Bypass REG1 to AGND through a 1µF
ceramic capacitor.
Analog Ground
Accurate 3V Buffered Reference Output. Connect REF to DIM through a resistive voltage-divider to
apply a DC voltage for analog-controlled dimming functionality. Leave REF unconnected if unused.
Dimming Control Input. Connect DIM to an external PWM signal for PWM dimming. For analog-
controlled dimming, connect DIM to REF through a resistive voltage-divider. The dimming frequency
is 200Hz under these conditions. Connect DIM to AGND to turn off the LEDs.
SYNC Input/Output. The PWM clock is generated by the RTSYNC oscillator. Connect an external
resistor to RTSYNC to select a clock switching frequency from 125kHz to 600kHz or connect RTSYNC
to an external clock to synchronize the MAX16831 with a master clock signal.
Clock Output. CLKOUT buffers the oscillator/clock. Connect CLKOUT to the SYNC input of another
device to operate the MAX16831 in a multichannel configuration. CLKOUT is a logic output.
Internally Connected. Must be connected to AGND.
Error-Amplifier Output. Connect the compensation network from COMP to FB for stable closed-loop
control. Use low-leakage ceramic capacitors in the feedback network.
Current-Sense Amplifier Output. The current-sense amplifier (CSA) senses the differential voltage
across the load sense resistor, R
current. Connect the proper compensation resistor from CS to FB.
Error-Amplifier Inverting Input
Overvoltage Protection Input. Connect OV to HI through a resistive voltage-divider to set the
overvoltage limit for the load. When the voltage at OV exceeds the 1.235V (typ) threshold, an
overvoltage fault is generated and the switching MOSFET turns off. The MOSFET is turned on again
when the voltage at OV drops below 1.17V (typ).
Switching Ground. SGND is the ground for non-analog and high-current gate driver circuitry.
Gate Driver Output. Connect DRV to the gate of an external n-channel MOSFET for switching.
Gate Driver Supply Input. Connect DRI to REG2 to power the primary switching MOSFET driver.
Bypass DRI to AGND through a 10µF ceramic capacitor.
Positive Peak Current-Sense Input. Connect SNS+ to the positive side of the switch current-sense
resistor, R
Negative Peak Current-Sense Input. Connect SNS- to the negative side of the switch current-sense
resistor, R
Analog Ground. Ensure a low-impedance connection between QGND and AGND.
Dimming Gate Driver Output. Connect DGT to the gate of an external n-channel MOSFET for
dimming. DGT is powered by the internal regulator, CLMP, and is referenced to LO.
SENSE
SENSE
.
.
CS
, and generates a voltage, V
FUNCTION
CC
CC
to use the 6.0V (max) default UVLO
through a resistive voltage-divider to
CS
, at CS proportional to the LED
Pin Description
CC
>