LM3500TL-21/NOPB National Semiconductor, LM3500TL-21/NOPB Datasheet - Page 2
![IC LED DRVR WHT BCKLT 8-MICROSMD](/photos/7/37/73791/tla08ssa_sml.jpg)
LM3500TL-21/NOPB
Manufacturer Part Number
LM3500TL-21/NOPB
Description
IC LED DRVR WHT BCKLT 8-MICROSMD
Manufacturer
National Semiconductor
Type
Backlight, White LEDr
Datasheet
1.LM3500TL-21NOPB.pdf
(20 pages)
Specifications of LM3500TL-21/NOPB
Topology
PWM, Step-Up (Boost)
Number Of Outputs
1
Internal Driver
Yes
Type - Primary
Backlight
Type - Secondary
White LED
Frequency
850kHz ~ 1.15MHz
Voltage - Supply
2.7 V ~ 7 V
Voltage - Output
19.5 V ~ 20.5 V
Mounting Type
Surface Mount
Package / Case
8-MicroSMD
Operating Temperature
-40°C ~ 85°C
Current - Output / Channel
640mA
Internal Switch(s)
Yes
Efficiency
85%
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
LM3500TL-21
LM3500TL-21TR
LM3500TL-21TR
www.national.com
Output Voltage
Connection Diagram
Ordering Information
Pin Description/Functions
AGND(pin A1): Analog ground pin. The analog ground pin
should tie directly to the GND pin.
V
with a capacitor, as close to the device as possible, connected
between the V
V
device. Connect the output capacitor between the V
GND pins as close as possible to the device.
V
switch devices. Keep the inductor connection close to this pin
to minimize EMI radiation.
GND(pin C3): Power ground pin. Tie directly to ground plane.
Maximum
IN
OUT
SW
(pin B1): Analog and Power supply pin. Bypass this pin
Pin
(pin C2): Drain connection of internal NMOS and PMOS
16V
16V
21V
21V
A1
B1
C1
C2
C3
B3
A3
A2
(pin C1): Source connection of internal PMOS power
IN
and GND pins.
LM3500TLX-16
LM3500TLX-21
Order Number
LM3500TL-16
LM3500TL-21
AGND
SHDN
Name
V
GND
V
NC
V
FB
OUT
SW
IN
Analog ground.
Analog and Power supply input.
PMOS source connection for synchronous rectification.
Switch pin. Drain connections of both NMOS and PMOS power devices.
Power Ground.
Output voltage feedback connection.
No internal connection made to this pin.
Shutdown control pin.
Package Type
micro SMD
micro SMD
micro SMD
micro SMD
OUT
8-bump micro SMD
and
Top View
2
FB(pin B3): Output voltage feedback connection. Set the pri-
mary White LED network current with a resistor from the FB
pin to GND. Keep the current setting resistor close to the de-
vice and connected between the FB and GND pins.
NC(pin A3): No internal connection is made to this pin. The
maximum allowable voltage that can be applied to this pin is
7.5V.
SHDN(pin A2): Shutdown control pin. Disable the device with
a voltage less than 0.3V and enable the device with a voltage
greater than 1.1V. The white LED current can be controlled
using a PWM signal at this pin. There is an internal pull down
on the SHDN pin, the device is in a normally off state.
NSC Package
TL08SSA
TL08SSA
TL08SSA
TL08SSA
Drawing
Function
20065702
Top Mark
S18
S18
S23
S23
250 Units, Tape and Reel
3000 Units, Tape and Reel
250 Units, Tape and Reel
3000 Units, Tape and Reel
Supplied As