LM3405AXMK/NOPB National Semiconductor, LM3405AXMK/NOPB Datasheet - Page 8
![IC LED DRVR HP CONST TSOT23-6](/photos/6/60/66084/pkg_mk06a_sml.jpg)
LM3405AXMK/NOPB
Manufacturer Part Number
LM3405AXMK/NOPB
Description
IC LED DRVR HP CONST TSOT23-6
Manufacturer
National Semiconductor
Series
PowerWise®r
Type
High Power, Constant Currentr
Datasheet
1.LM3405AXMKNOPB.pdf
(20 pages)
Specifications of LM3405AXMK/NOPB
Constant Current
Yes
Topology
PWM, Step-Down (Buck)
Number Of Outputs
1
Internal Driver
Yes
Type - Primary
Flash/Torch
Type - Secondary
High Brightness LED (HBLED), White LED
Frequency
1.2MHz ~ 1.9MHz
Voltage - Supply
3 V ~ 22 V
Mounting Type
Surface Mount
Package / Case
TSOT-23-6, TSOT-6
Operating Temperature
-40°C ~ 125°C
Current - Output / Channel
1A
Internal Switch(s)
Yes
Efficiency
92%
For Use With
LM3405AEVAL - BOARD EVAL FOR LM3405
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Output
-
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
Other names
LM3405AXMKTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM3405AXMK/NOPB
Manufacturer:
DIODES
Quantity:
31 600
www.national.com
The fourth method can be used in an application which has
an external low voltage rail, V
D2 from V
Again for best performance, ensure that the gate drive volt-
age, V
SETTING THE LED CURRENT
LM3405A is a constant current buck regulator. The LEDs are
connected between V
Typical Application Circuit. The FB pin is at 0.205V in regu-
lation and therefore the LED current I
resistor R1 from FB to ground by the following equation:
I
and therefore R1 minimum must be approximately 0.2Ω. I
should also be kept above 200mA for stable operation, and
therefore R1 maximum must be approximately 1Ω. If average
LED currents less than 200mA are desired, the EN/DIM pin
can be used for PWM dimming. See LED PWM DIMMING
section.
OUTPUT VOLTAGE
The output voltage is primarily determined by the number of
LEDs (n) connected from V
can be written as :
where V
current level (see LED manufacturer datasheet for forward
characteristics curve).
ENABLE MODE / SHUTDOWN MODE
The LM3405A has both enable and shutdown modes that are
controlled by the EN/DIM pin. Connecting a voltage source
greater than 1.8V to the EN/DIM pin enables the operation of
LM3405A, while reducing this voltage below 0.4V places the
part in a low quiescent current (0.3µA typical) shutdown
mode. There is no internal pull-up on EN/DIM pin, therefore
an external signal is required to initiate switching. Do not allow
this pin to float or rise to 0.3V above V
that when the EN/DIM pin voltage rises above 1.8V while the
input voltage is greater than UVLO, there is a finite delay be-
fore switching starts. During this delay the LM3405A will go
through a power on reset state after which the internal soft-
start process commences. The soft-start process limits the
inrush current and brings up the LED current (I
and controlled fashion. The total combined duration of the
power on reset delay, soft-start delay and the delay to fully
establish the LED current is in the order of 100µs (refer to
Figure 10).
The simplest way to enable the operation of LM3405A is to
connect the EN/DIM pin to V
LM3405A whenever the input voltage is applied. However,
when an input voltage of slow rise time is used to power the
application and if both the input voltage and the output voltage
are not fully established before the soft-start time elapses, the
control circuit will command maximum duty cycle operation of
the internal power switch to bring up the output voltage rapid-
ly. When the feedback pin voltage exceeds 0.205V, the duty
cycle will have to reduce from the maximum value according-
ly, to maintain regulation. It takes a finite amount of time for
this reduction of duty cycle and this will result in a spike in LED
current for a short duration as shown in Figure 6. In applica-
tions where this LED current overshoot is undesirable, EN/
DIM pin voltage can be separately applied and delayed such
that V
reaches the enable threshold. The effect of delaying EN/DIM
F
should not exceed the 1A current capability of LM3405A
IN
EXT
F
is fully established before the EN/DIM pin voltage
- V
is the forward voltage of one LED at the set LED
EXT
D2
, independent of V
+ V
V
D1
OUT
, falls in the range of 2.5V to 5.5V.
OUT
I
= ((n x V
F
= V
and the FB pin as shown in the
OUT
EXT
FB
IN
to FB pin and therefore V
which allows self start-up of
. C3 can be charged through
/ R1
IN
F
) + V
and V
FB
IN
F
. It should be noted
)
OUT
is set by V
voltage levels.
F
) in a smooth
FB
and
OUT
F
8
with respect to V
For a fast rising input voltage (200µs for example), there is no
need to delay the EN/DIM signal since soft-start can smoothly
bring up the LED current as shown in Figure 8.
FIGURE 7. Startup Response to V
FIGURE 8. Startup Response to V
FIGURE 6. Startup Response to V
IN
on the LED current is shown in Figure 7.
IN
IN
IN
with EN/DIM delayed
with 200µs rise time
with 5ms rise time
30015276
30015277
30015275