LDS8620-002-T2 IXYS, LDS8620-002-T2 Datasheet - Page 6

• Manufacturer Part Number: LDS8620-002-T2
• Description: IC LED DRIVER FLASH 16WQFN
• Manufacturer: IXYS
• Series: PowerLite™r
• Type: Photo Flash LEDr

Specifications of LDS8620-002-T2

• Topology: Linear (LDO), Switched Capacitor (Charge Pump)
• Number Of Outputs: 2
• Internal Driver: Yes
• Type - Primary: Flash/Torch
• Frequency: 1.1MHz
• Voltage - Supply: 2.7 V ~ 5.5 V
• Mounting Type: Surface Mount
• Package / Case: 16-WQFN Exposed Pad, 16-DQFN
• Operating Temperature: -40°C ~ 85°C
• Current - Output / Channel: 96mA
• Internal Switch(s): Yes
• Efficiency: 95%
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Lead Free Status / Rohs Status: Details
• Other names: LDS8620-002-T2-2

LDS8620
PIN DESCRIPTION
PIN FUNCTION
V
ceramic bypass capacitor is required between the Vin
pin and ground near the device. The operating input
voltage range is from 2.7V to 5.5V. Whenever the
input supply falls below the under-voltage threshold
(2.1 V), all the LED channels are disabled and the
device enters shutdown mode.
EN/SET is the enable and one wire addressable
control logic input for all LED channels. Guaranteed
levels of logic high and logic low are set at 1.3 V and
0.4 V respectively. When EN/SET is initially taken
high, the device becomes enabled and all LED
currents remain at 0 mA. To place the device into
zero current mode, the EN/SET pin must be held low
for more than 1.5 ms.
V
the LED anodes. A small 1μ F ceramic bypass
© 2009 IXYS Corp.
Characteristics subject to change without notice
13 - 15
IN
OUT
Pin #
4 - 6
PAD
10
11
12
16
is the supply pin for the charge pump. A small 1
1
2
3
7
8
9
is the charge pump output that is connected to
EN/SET
Name
LEDA
LEDB
GND
V
C1+
C2+
PAD
C1-
C2-
NC
NC
V
OUT
IN
No connect
LED A cathode terminal
LED B cathode terminal
No connect
Charge pump output connected to the LED anodes
Charge pump input, connect to battery or supply
Bucket capacitor 1 Positive terminal
Bucket capacitor 1 Negative terminal
Bucket capacitor 2 Positive terminal
Bucket capacitor 2 Negative terminal
Ground Reference, Connect all these pins to GND
Device enable (active high) and LED Current
Dimming Control
Connect to GND on the PCB
Function
μ
F
6
capacitor is required between the Vout pin and
ground near the device.
GND is the ground reference for the charge pump.
The pin must be connected to the ground plane on
the PCB.
C1+, C1- are connected to each side of the ceramic
bucket capacitor C1
C2+, C2- are connected to each side of the ceramic
bucket capacitor C2
LEDA and LEDB provide the internal regulated
current source for each of the LED cathodes. These
pins
whenever the device is in shutdown mode.
PAD is the exposed pad underneath the package.
For best thermal performance, the pad should be
soldered to the PCB and connected to the ground
plane
enter
high-impedance
Top view: TQFN 16-lead 3 X 3 mm
Doc. No. 8620DS, Rev. N1.1
zero
current
state