BD6067GU-E2 Rohm Semiconductor, BD6067GU-E2 Datasheet - Page 14

• Manufacturer Part Number: BD6067GU-E2
• Description: IC LED DRIVR WHITE BCKLGT 8-VCSP
• Manufacturer: Rohm Semiconductor
• Type: Backlight, White LEDr

Specifications of BD6067GU-E2

• Topology: PWM, Step-Up (Boost)
• Number Of Outputs: 1
• Internal Driver: Yes
• Type - Primary: Backlight
• Type - Secondary: White LED
• Frequency: 800kHz ~ 1.2MHz
• Voltage - Supply: 2.7 V ~ 5.5 V
• Voltage - Output: 30V
• Mounting Type: Surface Mount
• Package / Case: 8-VCSP
• Operating Temperature: -30°C ~ 85°C
• Current - Output / Channel: 30mA
• Internal Switch(s): Yes
• Led Driver Application: Mobile Phones
• No. Of Outputs: 1
• Output Current: 30mA
• Output Voltage: 36V
• Input Voltage: 2.7V To 5.5V
• Operating Temperature Range: -30°C To +85°C
• Driver: RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Efficiency: -
• Lead Free Status / Rohs Status: Details
• Other names: BD6067GU-E2TR

© 2011 ROHM Co., Ltd. All rights reserved.
BD6067GU, BD6069GUT, BD6071HFN, BD6072HFN
►BD6071HFN
●Start control and brightness control
www.rohm.com
2-1) The continuous time the brightness adjustment is made by giving DC control voltage to VFB pin of BD6068GUT /
BD6071HFN can control the start conditions by its EN terminal, and power off at 0.4V or below, and power on at 1.4V or
higher. And by changing the duty of power on and off by PWM control, the LED brightness can be adjusted.
Two techniques are available for the brightness adjustment. One is discrete time (PWM) adjustment, and the other is
continuous time adjustment.
1) PWM brightness adjustment is made by giving PWM signal to EN as shown in Fig.38.
The BD6068GU/BD6071HFN T power on/off are according to the PWM signal. By this method, LED current is controlled
from 0 to the maximum current. The average LED current increases in proportion with the duty cycle of PWM signal. While
in PWM off-cycle mode, the IC and LED both consume no currents, thus providing a high-efficiency operation. And please
don’t use duty less than 5% or more than 95% of current setting for the brightness adjustment because of the influence of
turning on and off operating is large. The recommended PWM frequency is 100Hz ~ 300Hz.
BD6071HFN via a series resistor as shown in Fig.39. LED luminance (current) changed by giving DC voltage to VFB
directly. DC voltage is given from filtered one of DAC signal, or PWM signal shown in Fig.41. The advantage of this
approach is that the PWM signal to be used to control the LED brightness can be set to a high frequency (1kHz or higher).
And please don’t use duty less than 5% or more than 95% of current setting for the brightness adjustment.
VIN
VIN
Fig.41 The brightness adjustment example of
Fig.39 The brightness adjustment example by DAC
LED current (ILED) is approximated by the following equation.
ILED = [{(VFB-DAC) / R1} × R2 + VFB ] / RFB
VFB terminal by PWM (f
Fig.38 The brightness adjustment example of EN terminal by PWM (f
VIN
TEST
EN
VIN
TEST
EN
GNDA
GNDA
0 ～ 2.85V
GND
GND
22μH
22μH
10kHz
PWM
VIN
VOUT
VOUT
VFB
PWM
VFB
PWM
SW
SW
100kΩ
=10kHz)
22kΩ
DAC
47kΩ
33kΩ
47nF
4.7kΩ
R1
1μF
1μF
R2
VIN
TEST
EN
GNDA
RFB
30Ω
24Ω
ILED
ILED
14/29
GND
22µH
VOUT
VFB
SW
30
25
20
15
10
1µF
-5
5
0
30
25
20
15
10
-5
5
0
25
20
15
10
5
0
0
0
0
24Ω
Fig.40 DAC adjustment
0.5
0.5
10
Fig.42 VFB PWM Control
PWM
(VFB=500mV)
20
1
1
30
= 100Hz ~ 300Hz)
1.5
1.5
40
HI Duty [%]
DAC [V]
2
50
2
60
2.5
2.5
70
3
3
80
2011.01 - Rev.C
Technical Note
3.5
3.5
90
100
4
4