ISL6142CB Intersil, ISL6142CB Datasheet - Page 19
![IC CONTROLLER HOT PLUG 14-SOIC](/photos/5/65/56531/20-14-soic_sml.jpg)
ISL6142CB
Manufacturer Part Number
ISL6142CB
Description
IC CONTROLLER HOT PLUG 14-SOIC
Manufacturer
Intersil
Type
Hot-Swap Controllerr
Datasheet
1.ISL6142CBZA.pdf
(23 pages)
Specifications of ISL6142CB
Applications
General Purpose, VoIP
Internal Switch(s)
No
Voltage - Supply
36 V ~ 72 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
14-SOIC (0.154", 3.90mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
be found, then consider 2 separate resistor dividers (one for
each pin, both from V
adjust or trim either trip point independently. Some
applications employ a short pin ground on the connector tied
to R4 to ensure the hot plug device is fully powered up
before the UV and OV pins (tied to the short pin ground) are
biased. This ensures proper control of the GATE is
maintained during power up. This is not a requirement for the
ISL6142/52 however the circuit will perform properly if a
short pin scheme is implemented (reference Figure 38).
Applications: PWRGD/PWRGD
The PWRGD/PWRGD outputs are typically used to directly
enable a power module, such as a DC/DC converter. The
PWRGD (ISL6142) is used for modules with active low
enable (L version), and PWRGD (ISL6152) for those with an
active high enable (H version). The modules usually have a
pull-up device built-in, as well as an internal clamp. If not, an
external pull-up resistor may be needed. If the pin is not
used, it can be left open.
For both versions at initial start-up, when the DRAIN to V
voltage differential is less than 1.3V and the GATE voltage is
within 2.5V (V
power is considered good and the PWRGD/PWRGD pins
will go active. At this point the output is latched and the
comparators above no longer control the
second DRAIN comparator remains active and will drive the
PWRGD/PWRGD output inactive if the DRAIN voltage
exceeds V
the signals that shut off the GATE (Over-Voltage, Under-
Voltage; Under-Voltage-Lock-Out; Over-Current Time-Out,
disable pin high, or powering down). In this case the
PWRGD/PWRGD output will go inactive, indicating power is
no longer good.
ISL6142 (L version; Figure 34): Under normal conditions
(DRAIN voltage - V
the Q2 DMOS will turn on, pulling PWRGD low, enabling the
module.
When any of the 5 conditions occur that turn off the GATE
(OV, UV, UVLO, Over-Current Time-Out, disable pin high)
the PWRGD latch is reset and the Q2 DMOS device will shut
off (high impedance). The pin will quickly be pulled high by
the external module (or an optional pull-up resistor or
equivalent) which in turn will disable it. If a pull-up resistor is
used, it can be connected to any supply voltage that doesn’t
exceed the IC pin maximum ratings on the high end, but is
high enough to give acceptable logic levels to whatever
EE
by more than 8V. The latch is reset by any of
GH
) of its normal operating voltage (13.6V),
EE
DD
< V
to -V
PG
19
, and ∆V
IN
). This also allows the user to
GATE
output.
- V
GATE
However a
< V
ISL6142, ISL6152
GH
EE
)
signal it is driving. An external clamp may be used to limit the
voltage range.
The PWRGD can also drive an opto-coupler (such as a
4N25), as shown in Figure 35 or LED (Figure 36). In both
cases, they are on (active) when power is good. Resistors
R13 or R14 are chosen based on the supply voltage, and the
amount of current needed by the loads.
ISL6152 (H version; Figure 37): Under normal conditions
(DRAIN voltage - V
the Q3 DMOS will be on, shorting the bottom of the internal
resistor to V
external module is high enough, the voltage drop across the
6.2kΩ resistor will look like a logic high (relative to DRAIN).
Note that the module is only referenced to DRAIN, not V
∆ V
GATE
FIGURE 35. ACTIVE LOW ENABLE OPTO-ISOLATOR
GATE
V
V
V
V
(SECTION OF) ISL6142
(SECTION OF) ISL6142
EE
EE
+
+
-
-
FIGURE 34. ACTIVE LOW ENABLE MODULE
V
PG
DH
COMPARATORS
COMPARATORS
GH
FIGURE 36. ACTIVE LOW ENABLE LED
EE
(L VERSION)
(L VERSION)
(SECTION OF) ISL6142
LATCH
LATCH
LOGIC
LOGIC
, turning Q2 off. If the pull-up current from the
+
+
+
-
-
-
V
V
VDD
DD
DD
(L VERSION)
EE
DRAIN
< V
LATCH
LOGIC
PG
Q2
Q2
V
V
, and ∆V
EE
EE
Q2
V
EE
PWRGD
PWRGD
GATE
PWRGD
DRAIN
DRAIN
CL
- V
+
GATE
LED (GREEN)
R13
R14
OPTO
ACTIVE LOW
VIN-
VIN+
ON/OFF
MODULE
ENABLE
< V
PWRGD
VOUT-
GH
VOUT+
EE
),