MIC2580A-1.0BTS TR Micrel Inc, MIC2580A-1.0BTS TR Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/4/434/micrel_inc_sml.jpg)
MIC2580A-1.0BTS TR
Manufacturer Part Number
MIC2580A-1.0BTS TR
Description
IC CTRLR PCI HOT SWAP 24-TSSOP
Manufacturer
Micrel Inc
Type
Hot-Swap Controllerr
Datasheet
1.MIC2580A-1.0YTS.pdf
(21 pages)
Specifications of MIC2580A-1.0BTS TR
Applications
General Purpose, CompactPCI™
Internal Switch(s)
No
Voltage - Supply
3.3V, 5V, ±12V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
24-TSSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
MIC2580A-1.0BTSTR
MIC2580A-1.0BTSTR
MIC2580A-1.0BTSTR
February 2005
MIC2580A
Pin Number
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
7
8
9
/EPWRGD
M12VOUT
Pin Name
5VSENSE
/LPCIRST
/PWRGD
CSTART
5VGATE
VPCHG
M12VIN
CSLEW
/FAULT
5VOUT
12VIN
CRST
/POR
GND
5VIN
/ON
Pin Function
Local PCI Reset (Open-Drain Output): Local PCI reset output to PCI
controller. Compliant to CompactPCI specification for LOCAL_PCI_RESET.
Early Power Good (Open-Drain Output): This signal goes active should
/FAULT or /PWRGD go active. No deglitch filtering is provided. This signal
satisfies PCI /RST timing for T
sion 2.1.
Power Good (Open-Drain Output): Active-low output goes active when all
supplies are within tolerance. (A 20µs delay is inserted prior to activation to
reduce nuisance tripping.)
Precharge Supply (Output): (MIC2580A-1.0) +1V ±20% supply used for
precharge bias for I/O terminations (CompactPCI only).
Ground
–12V Supply (Input): Input for internal –12V switch.
–12V Switched Supply (Output): Switched –12V supply to PCI Hot Plug
compliant socket. Load carrying output.
On-Off Control (Input): Logic low turns on all switches; logic high turns off all
switches. Also used to reset the device from a circuit breaker condition. The
/ON pin is edge-triggered and requires a high-to-low transition once all four
supplies are above their respective thresholds.
Reset Delay (External Component): Connect to external capactior (C
increase power-on reset delay.
Reset (Open-Drain Output): Active-low signal remains active for a time
determined by C
active. This signal may be used as a reset for logic controllers.
Slew (External Component): Connect to external capacitor (C
program the output slew rate of 3VGATE, 5VGATE, 12VGATE (internal) and
M12VGATE (internal).
Start-Up Timer (External Component): Connect to external capacitor
(C
start-up. Used to prevent nuisance tripping during turn-on of supplies.
Fault (Open-Drain Output/Input): This active-low output signal activated
upon overcurrent or thermal shutdown. Includes 20µs deglitch filter. Fault is
reset using /ON.
Forcing pin low turns off all switches but does not activate the circuit breaker
function.
5V Supply (Input): +5V-supply input for current monitoring (reference
voltage for 5VSENSE). Not a load-current carrying input.
+5V Current Sense (Input): Measures voltage drop across an external
sense resistor with respect to 5VIN for overcurrent detection through the +5V
switch.
+5V Output Voltage Sense (Input): Connect to source of external N-channel
MOSFET (+5V switched output) to monitor for output undervoltage condi-
tions.
5V Gate Drive (Output): Drives gate of external N-channel MOSFET +5V
switch. Adding capacitance will slow the slew rate of the external MOSFET
switch turn-on. (The external MOSFET’s gate is charged by an internal
current source.)
12V Supply (Input): MIC2580A power supply and input for internal +12
switch. Supplies power for internal circuitry.
START
) to increase the filter delay used to gate the /FAULT output upon
3
RST
after all supplies are within tolerance; i.e., /PWRGD is
FAIL
per PCI Local Bus Specification, ver-
SLEW
) to
Micrel, Inc.
MIC2580A
RST
) to