MAX5901ABEUT+T Maxim Integrated Products, MAX5901ABEUT+T Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX5901ABEUT+T
Manufacturer Part Number
MAX5901ABEUT+T
Description
IC HOT-SWAP CONTROLLER SOT23-6
Manufacturer
Maxim Integrated Products
Series
Simple Swapper™r
Type
Hot-Swap Controllerr
Datasheet
1.MAX5901ACEUTT.pdf
(14 pages)
Specifications of MAX5901ABEUT+T
Applications
General Purpose
Internal Switch(s)
No
Voltage - Supply
-9 V ~ -100 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
SOT-23-6
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
After power is applied, or ON/OFF is released, there is
a 300ms delay (t
This delay is also the automatic restart time delay.
In the event of a circuit-breaker condition or an over-
temperature fault condition, the turn-off delay is less
than 2µs. An undervoltage condition must exist for at
least 20ms (t
off the external MOSFET. ON/OFF must be held low for
at least 20ms (t
off the external MOSFET. Turn-off delay minimizes spu-
rious shutdowns due to noisy signals or momentary
Figure 2. Programmed -20V Lockout With Optional
Optocoupler On/Off Control
Figure 3. Power-Supply Sequencing
OPTIONAL
ON/OFF
DGND
-48V
GND
GND
V
EE
OFF
OFF
) before the MAX5900/MAX5901 turn
ON
_______________________________________________________________________________________
Turn-On and Turn-Off Delays
) before the MAX5900/MAX5901 turn
) before the gate ramp is started.
C
-100V, SOT23/TDFN, Simple Swapper
2C
R2
47kΩ
HOT-SWAP CONTROLLER #1
HOT-SWAP CONTROLLER #2
R1
3kΩ
GND
ON/OFF
GND
ON/OFF
V
V
EE
EE
MAX5900
MAX5900
MAX5901
MAX5901
HOT-SWAP CONTROLLER
GND
ON/OFF
V
EE
MAX5900
MAX5901
voltage spikes, as well as preventing accidental
resetting of the circuit-breaker latch (MAX5900L/
MAX5901L).
A thermal shutdown feature helps protect the external
MOSFET. If the die temperature of the MAX5900/
MAX5901 exceeds +125°C, the MOSFET is turned off.
For accurate performance, the MAX5900/MAX5901
must be in close thermal contact with the external
MOSFET (see the Layout Guidelines section). Due to
the low power dissipation of the MAX5900/MAX5901, its
junction temperature will typically be within a few
degrees of the MOSFET. All versions of the MAX5900/
MAX5901 automatically restart from a temperature fault
when the junction temperature drops below +110°C.
The MAX5900/MAX5901 turn off the external MOSFET if
the magnitude of the input voltage is below the level set
by ON/OFF for longer than 20ms (t
left unconnected, the lockout voltage (V
to -31.5V. V
the power-supply range by using external resistors. To
set the lockout voltage to a value between -9V and
-100V, use a resistor-divider connected between GND
and V
to ON/OFF. For example, use a 3kΩ resistor (R1 in
Figure 2) from ON/OFF to V
resistor, R2, using:
where V
V
the Electrical Characteristics table (typically 1.26V).
Figure 2 shows an example circuit with V
-20V. To defeat the UVLO, simply connect a single 100kΩ
resistor between ON/OFF and GND, as shown in Figure 4.
Figure 4. Defeating Undervoltage Lockout
ON/OFF
Hot-Swap Controllers
EE
, with the center node of the divider connected
UVLO
is the ON/OFF reference threshold specified in
-48V
GND
UVLO
R
2
is the desired lockout voltage, and
=
may also be set to any value within
R
1
100kΩ
×
⎛
⎜
⎝
Undervoltage Lockout
V
1 26
UVLO
HOT-SWAP CONTROLLER
EE
.
GND
ON/OFF
V
EE
Thermal Shutdown
and calculate the other
MAX5901
MAX5900
−
OFF
1
⎞
⎟
⎠
). If ON/OFF is
UVLO
UVLO
) defaults
set for
7