LT3092EST#TRPBF Linear Technology, LT3092EST#TRPBF Datasheet - Page 11
![IC PROG CURRENT SOURCE SOT223-3](/photos/7/35/73514/sot-223-3_05-08-1630_sml.jpg)
LT3092EST#TRPBF
Manufacturer Part Number
LT3092EST#TRPBF
Description
IC PROG CURRENT SOURCE SOT223-3
Manufacturer
Linear Technology
Datasheet
1.LT3092ETS8TRMPBF.pdf
(22 pages)
Specifications of LT3092EST#TRPBF
Function
Current Source
Accuracy
±1%
Voltage - Input
1.2 ~ 40 V
Current - Output
200mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
SOT-223 (3 leads + Tab), SC-73, TO-261
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Sensing Method
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
capacitor on the lower impedance output, and the same
restrictions do not apply. Capacitors in the range of 0.1μF
to 1μF usually provide suffi cient bypassing on the input,
and the value of input capacitance may be increased
without limit.
If an application uses GND referred capacitors on the input
or output (particularly the input), pay attention to the length
of the lines powering and returning ground from the circuit.
In the case where long power supply and return lines are
coupled with low ESR input capacitors, application-specifi c
voltage spikes, oscillations and reliability concerns may
be seen. This is not an issue with LT3092 stability, but
rather the low ESR capacitor forming a high-Q resonant
tank circuit with the inductance of the input wires. Adding
series resistance with the input of the LT3092, or with the
input capacitor, often solves this. Resistor values of 0.1Ω
to 1Ω are often suffi cient to dampen this resonance.
Give extra consideration to the use of ceramic capacitors.
Ceramic capacitors are manufactured with a variety of di-
electrics, each with different behavior across temperature
and applied voltage. The most common dielectrics used
are specifi ed with EIA temperature characteristic codes of
Z5U, Y5V, X5R and X7R. The Z5U and Y5V dielectrics are
good for providing high capacitances in a small package,
APPLICATIONS INFORMATION
Figure 5. Ceramic Capacitor DC Bias Characteristics
–100
–20
–40
–60
–80
20
0
0
2
4
DC BIAS VOLTAGE (V)
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10μF
6
8
Y5V
X5R
10
12
14
3092 F05
16
but they tend to have strong voltage and temperature
coeffi cients as shown in Figures 5 and 6. When used with
a 5V regulator, a 16V 10μF Y5V capacitor can exhibit an
effective value as low as 1μF to 2μF for the DC bias voltage
applied and over the operating temperature range. The X5R
and X7R dielectrics result in more stable characteristics
and are more suitable for use as the output capacitor.
The X7R type has better stability across temperature,
while the X5R is less expensive and is available in higher
values. Care still must be exercised when using X5R and
X7R capacitors; the X5R and X7R codes only specify
operating temperature range and maximum capacitance
change over temperature. Capacitance change due to DC
bias with X5R and X7R capacitors is better than Y5V and
Z5U capacitors, but can still be signifi cant enough to drop
capacitor values below appropriate levels. Capacitor DC
bias characteristics tend to improve as component case
size increases, but expected capacitance at operating
voltage should be verifi ed.
Voltage and temperature coeffi cients are not the only
sources of problems. Some ceramic capacitors have a
piezoelectric response. A piezoelectric device generates
voltage across its terminals due to mechanical stress. In a
ceramic capacitor the stress can be induced by vibrations
in the system or thermal transients.
Figure 6. Ceramic Capacitor Temperature Characteristics
–100
–20
–40
–60
–80
40
20
0
–50
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10μF
–25
0
TEMPERATURE (°C)
25
50
Y5V
75
X5R
100
3092 F06
125
LT3092
11
3092fb