MAX16023LTAS12+T Maxim Integrated Products, MAX16023LTAS12+T Datasheet - Page 12
![IC BATTERY BACKUP 1.2V 8TDFN-EP](/photos/1/38/13897/8-tdfn_21-0137i_sml.jpg)
MAX16023LTAS12+T
Manufacturer Part Number
MAX16023LTAS12+T
Description
IC BATTERY BACKUP 1.2V 8TDFN-EP
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX16023LTAL12T.pdf
(17 pages)
Specifications of MAX16023LTAS12+T
Function
Back-Up Management
Battery Type
All Battery Types
Voltage - Supply
1.53 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-WDFN Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Battery-Backup Circuits with
Regulated Output Voltage
Many µP-based products require manual-reset capabili-
ty, allowing the operator, a test technician, or external
logic circuitry to initiate a reset. For the MAX16023/
MAX16024, a logic-low on MR asserts RESET. RESET
remains asserted while MR is low. When MR goes high,
RESET deasserts after a minimum of 145ms (t
has an internal 30kΩ pullup resistor to V
driven with TTL/CMOS logic levels or with open-
drain/collector outputs. Connect a normally open
momentary switch from MR to GND to create a manual-
reset function; external debounce circuitry is not
required. If MR is driven from a long cable or the device
is used in a noisy environment, connect a 0.1µF capaci-
tor from MR to GND to provide additional noise immunity.
The MAX16024’s BATT ON output goes high when in
battery-backup mode. Use BATT ON to indicate bat-
tery-switchover status.
The MAX16023/MAX16024 battery freshness seal dis-
connects the backup battery from internal circuitry and
OUT until V
tery connected to BATT is fresh when the final product
is used for the first time.
The internal freshness seal latch prevents BATT from
powering OUT until V
setting the latch. When V
BATT begins to power OUT.
To reenable the freshness seal (MAX16023/
MAX16024):
1) Connect a battery to BATT.
2) Bring V
3) Drive MR higher than V
4) Pull OUT to 0.
A µP’s reset input starts the µP in a known state. The
MAX16023/MAX16024 µP supervisory circuits assert a
reset to prevent code-execution errors during power-
up, power-down, and brownout conditions. RESET
asserts when V
remains low for at least 145ms (t
12
______________________________________________________________________________________
Reset Output (MAX16023/MAX16024)
CC
CC
Battery-On Indicator (MAX16024)
to 0.
is applied. This ensures the backup bat-
CC
is below the reset threshold and
CC
has come up for the first time,
(MAX16023/MAX16024)
Battery Freshness Seal
BATT
CC
Manual-Reset Input
+ 1.2V for at least 3µs.
subsequently turns off,
RP
) after V
CC
. MR can be
CC
RP
). MR
rises
above the reset threshold. RESET also asserts when
MR is low. RESET is available in both push-pull and
open-drain configurations.
The MAX16023 offers an additional undervoltage com-
parator. The output PFO goes low when the voltage at
PFI falls below its V
power-fail comparator include monitoring the input of the
power supply (such as a battery) before any voltage reg-
ulation to provide an early power-fail warning, so soft-
ware can conduct an orderly system shutdown. The
power-fail comparator has a typical input hysteresis of
V
dent of the reset circuit. Connect PFI to GND, if not used.
Fixed output voltages of 1.2V, 1.8V, 2.5V, 3.0V, and
3.3V are available for all devices. The regulator output
delivers up to 100mA of load current.
The MAX16024 is available with both fixed and
adjustable output-voltage options. Use an external
resistive divider network connected between OUT, SET,
and GND (Figure 2) to set the adjustable output voltage
from 1.8V to 5.25V. Connect SET to GND for parts with
fixed output voltage option.
Figure 2. Setting the Adjustable Output Voltage (MAX16024
Only)
PFI-HYS
1.53 TO 5.5V
0.1µF
TO µP
and is powered from OUT, making it indepen-
Power-Fail Comparator (MAX16023)
V
RESET
CC
PFT
MAX16024
threshold. Common uses for the
GND
OUT
SET
Regulator Output
V
V
OUT
SET
= 1.2V
= V
SET
R1
R2
(1 + R1/R2)
1.8V TO 5.25V
10µF