ISL6296DRZ-T Intersil, ISL6296DRZ-T Datasheet - Page 8

• Manufacturer Part Number: ISL6296DRZ-T
• Description: IC AUTHENTICATION BATTERY 8-TDFN
• Manufacturer: Intersil
• Series: FlexiHash™r

Specifications of ISL6296DRZ-T

• Function: Battery Authentication
• Battery Type: Li-Ion, Li-Pol, NiMH
• Voltage - Supply: 2.6 V ~ 4.8 V
• Operating Temperature: -25°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-TDFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

It is recommended that device authentication be done once
in a while to maximize its effectiveness. Before a new
challenge code can be accepted by the device, the SESL
register must be re-written again to ensure that the original
seeds are re-loaded from the OTP ROM into the hash
engine prior to performing the next authentication code
calculation. Failure to follow the sequence will result is a bus
error, causing the sBER flag to be set in the STAT register.
SET-UP FOR DEVICE AUTHENTICATION SUPPORT
To configure the host and the ISL6296 to support device
authentication function, the pack manufacturer will need to
select at least 2 sets of 32-bit secret codes. For greater
security, a third set of 32-bit secret may be used. The
FlexiHash™ engine requires two sets of 32-bit secrets for
use in its hash calculation: the first set to define its hash
function, and the second set to initialize its seed for hash
calculation. These two sets can be selected from the same
secret location. The chosen secret codes are to be kept by
the pack manufacturer and maintained at utmost
confidentiality.
After the secrets have been determined, they are written into
the device’s OTP ROM. After verification that the codes have
been written in correctly, the relevant secrets lock-out bits at
ROM address location 0-00 should be set. Once set, the
lock-out bits can no longer be cleared. Thereafter, read/write
access to the secret information will no longer be possible,
and the secret codes are made available only to the
FlexiHash™ engine for generation of authentication code
based on a challenge code input from the host.
On the host side, the same secret codes will need to be kept,
and the same FlexiHash™ engine will have to be
implemented in firmware. Refer to the application note
AN1166 for detailed information of firmware implementation.
It is important that the secret codes be stored scrambled in
the host’s non-volatile memory so that the secret information
cannot be easily revealed by monitoring signal transfer on
the host PCB.
FIGURE 4. AUTHENTICATION PROCESS FLOW DIAGRAM
32-bit Hash Function
32-bit Hash Function
32-bit Hash Seed
32-bit Hash Seed
64-bit Secret
64-bit Secret
8
FlexiHash
FlexiHash
Engine
Engine
challenge word from host
challenge word from host
32-bit pseudo-random
32-bit pseudo-random
8-bit authentication
8-bit authentication
code
code
ISL6296
THE HASH ENGINE
The hash engine consists of 4 separate programmable 8-bit
CRC calculators. Two sets of 32-bit secret codes are use by
the hash engine for authentication code generation. The first
set is used to define the CRC polynomial as well as the input
selection for each of the CRC calculators. The second is
used as initial seeds for the CRC calculations. Outputs of the
4 CRC calculators are logically combined to produce the
8-bit output of the overall FlexiHash™ engine. Block diagram
of the FlexiHash engine is illustrated in Figure 6. More
detailed description on the hash engine can be found in the
application note AN1166.
FIGURE 5. FLOW CHART FOR AUTHENTICATION PROCESS
SELECT HASH FUNCTION AND SEED
CHALLENGE TO CHLG REGISTER
BY WRITING TO SESL REGISTER
RESULT FROM AUTH REGISTER,
BASED ON THE SAME SECRETS
READ THE AUTHENTICATION
CALCULATE THE EXPECTED
THE TWO RESULTS MATCH?
WAKE UP ISL6296 USING A
AFTER WAITING FOR 1 BT
AUTHENTICATION RESULT
REGULAR BREAK SIGNAL
SEND A 32-BIT RANDOM
YES
START
END
D
THE SYSTEM
SHUT DOWN
NO
March 21, 2008
FN9201.2