LTC4002EDD-4.2#PBF Linear Technology, LTC4002EDD-4.2#PBF Datasheet - Page 10
![IC CHARGER BATTERY LI-ION 10-DFN](/photos/6/59/65943/10-dfn_pkg_sml.jpg)
LTC4002EDD-4.2#PBF
Manufacturer Part Number
LTC4002EDD-4.2#PBF
Description
IC CHARGER BATTERY LI-ION 10-DFN
Manufacturer
Linear Technology
Type
Battery Chargerr
Datasheet
1.LTC4002EDD-4.2PBF.pdf
(16 pages)
Specifications of LTC4002EDD-4.2#PBF
Function
Charge Management
Battery Type
Lithium-Ion (Li-Ion)
Voltage - Supply
4.7 V ~ 22 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
10-WFDFN Exposed Pad
Output Voltage
4.2V
Operating Supply Voltage (min)
4.7V
Operating Supply Voltage (max)
22V
Operating Temp Range
-40C to 85C
Package Type
DFN
Mounting
Surface Mount
Pin Count
10
Operating Temperature Classification
Industrial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
OPERATIO
LTC4002
The LTC4002 is a constant current, constant voltage
Li-Ion battery charger controller that uses a current mode
PWM step-down (buck) switching architecture. The charge
current is set by an external sense resistor (R
across the SENSE and BAT pins. The final battery float
voltage is internally set to 4.2V per cell. For batteries like
lithium-ion that require accurate final float voltage, the
internal 2.465V reference, voltage amplifier and the resis-
tor divider provide regulation with ±1% accuracy.
A charge cycle begins when the voltage at the V
above the UVLO level and is 250mV or more greater than
the battery voltage. At the beginning of the charge cycle,
if the battery voltage is less than the trickle charge thresh-
old, 2.9V for the 4.2 version and 5V for the 8.4 version, the
charger goes into trickle charge mode. The trickle charge
current is internally set to 10% of the full-scale current. If
the battery voltage stays low for 30 minutes, the battery
is considered faulty and the charge cycle is terminated.
When the battery voltage exceeds the trickle charge thresh-
old, the charger goes into the full-scale constant current
TEST CIRCUITS
10
1.5V
COMP
–
+
LT1006
LTC4002
U
15V
0V
100µA
Test Circuit 1
CA
VA
–
+
–
+
4.2V
4002 TC02
SENSE
BAT
CC
pin rises
R
10Ω
1mA
SENSE
SENSE
)
charge mode. In constant current mode, the charge cur-
rent is set by the external sense resistor R
internal 100mV reference; I
When the battery voltage approaches the programmed
float voltage, the charge current will start to decrease.
When the current drops to 25% (4.2 version) or 10% (8.4
version) of the full-scale charge current, an internal com-
parator turns off the internal pull-down N-channel MOSFET
at the CHRG pin, and connects a weak current source to
ground to indicate a near end-of-charge condition.
An internal 3 hour timer determines the total charge time.
After a time out occurs, the charge cycle is terminated
and the CHRG pin is forced high impedance. To restart
the charge cycle, remove and reapply the input voltage or
momentarily shut the charger down. Also, a new charge
cycle will begin if the battery voltage drops below the
recharge threshold voltage of 4.05V per cell.
When the input voltage is present, the charger can be shut
down (I
input voltage is not present, the charger goes into sleep
1.5V
CC
= 3mA) by pulling the COMP pin low. When the
COMP
–
+
LT1006
15V
0V
100µA
Test Circuit 2
LTC4002
BAT
CA
= 100mV/R
+
–
SENSE
BAT
SENSE
SENSE
R
10Ω
4002 TC01
V
SENSE
BAT
.
and an
4002f