NCP1200D40R2G ON Semiconductor, NCP1200D40R2G Datasheet - Page 7

• Manufacturer Part Number: NCP1200D40R2G
• Description: IC CTRLR PWM CM 8SOIC
• Manufacturer: ON Semiconductor

Specifications of NCP1200D40R2G

• Output Isolation: Isolated
• Frequency Range: 36 ~ 48kHz
• Voltage - Input: 11.4 ~ 16 V
• Operating Temperature: -25°C ~ 150°C
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Number Of Pwm Outputs: 1
• On/off Pin: No
• Adjustable Output: No
• Topology: Flyback/Forward
• Switching Freq: 42KHz
• Duty Cycle: 80%
• Operating Supply Voltage (max): 16V
• Output Current: 250A
• Synchronous Pin: No
• Rise Time: 67ns
• Fall Time: 28ns
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SOIC N
• Number Of Outputs: 1
• Duty Cycle (max): 80 %
• Mounting Style: SMD/SMT
• Switching Frequency: 42 KHz
• Operating Supply Voltage: 16 V
• Maximum Operating Temperature: + 150 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: NCP1200D40R2GOS; NCP1200D40R2GOS; NCP1200D40R2GOSTR

INTRODUCTION
architecture where the switch−off time is dictated by the
peak current setpoint. This component represents the ideal
candidate where low part−count is the key parameter,
particularly in low−cost AC−DC adapters, auxiliary
supplies etc. Due to its high−performance High−Voltage
technology, the NCP1200 incorporates all the necessary
components normally needed in UC384X based supplies:
timing components, feedback devices, low−pass filter and
self−supply. This later point emphasizes the fact that ON
Semiconductor’s NCP1200 does NOT need an auxiliary
winding to operate: the product is naturally supplied from
the high−voltage rail and delivers a V
system is called the Dynamic Self−Supply (DSS).
consumption and the MOSFET’s gate charge, Qg. If we
select a MOSFET like the MTD1N60E, Qg equals 11 nC
(max). With a maximum switching frequency of 48 kHz (for
the P40 version), the average power necessary to drive the
MOSFET (excluding the driver efficiency and neglecting
various voltage drops) is:
Fsw = maximum switching frequency
Qg = MOSFET’s gate charge
V
consumption, simply divide this result by V
at no−load will therefore heavily rely on the internal IC
consumption plus the above driving current (altered by the
driver’s efficiency). Suppose that the IC is supplied from a
400 V DC line. To fully supply the integrated circuit, let’s
imagine the 4 mA source is ON during 8 ms and OFF during
50 ms. The IC power contribution is therefore: 400 V . 4 mA
Fsw @ Qg @ V
Fsw @ Qg
CC
The NCP1200 implements a standard current mode
The DSS behavior actually depends on the internal IC
To obtain the final driver contribution to the IC
= V
GS
= 530 mA. The total standby power consumption
level applied to the gate
cc
with
10.6 V Avg.
10.00M
CC
Figure 15. The Charge/Discharge Cycle
to the IC. This
APPLICATIONS INFORMATION
CC
V
CCOFF
Over a 10 mF V
: Idriver =
30.00M
http://onsemi.com
ON
= 11.4 V
50.00M
7
CC
Output Pulses
Dynamic Self−Supply
V
can easily describe the current source operation with a bunch
of simple logical equations:
is ON, no output pulses
OFF, output is pulsing
ON, output is pulsing
sketch offers the necessary light:
. 0.16 = 256 mW. If for design reasons this contribution is
still too high, several solutions exist to diminish it:
V
CC
CCON
Capacitor
The DSS principle is based on the charge/discharge of the
POWER−ON: IF V
IF V
IF V
Typical values are: V
To better understand the operational principle, Figure 15’s
Filter
EMI
1. Use a MOSFET with lower gate charge Qg
2. Connect pin through a diode (1N4007 typically) to
Figure 16. A simple diode naturally reduces the
70.00M
bulk capacitor from a low level up to a higher level. We
one of the mains input. The average value on pin 8
becomes
example drops to: 160 mW.
CC
CC
= 9.8 V
OFF
increasing < V
decreasing > V
90.00M
2 * V mains PEAK
average voltage on pin 8
CC
4.7 mF
400 V
CCOFF
p
V
Current
Source
< V
CC
C3
CCOFF
CCON
CCOFF
= 11.4 V, V
+
THEN Current Source is
THEN Current Source is
. Our power contribution
THEN Current Source
1
2
3
4
NCP1200
Adj
FB
CS
GND Drv
CCON
1N4007
Dstart
V
NC
HV
CC
= 9.8 V
8
7
6
5