NCP1010ST100T3 ON Semiconductor, NCP1010ST100T3 Datasheet - Page 11
![IC OFFLINE SWIT SMPS CM SOT223](/photos/26/98/269860/sot223_sml.jpg)
NCP1010ST100T3
Manufacturer Part Number
NCP1010ST100T3
Description
IC OFFLINE SWIT SMPS CM SOT223
Manufacturer
ON Semiconductor
Datasheet
1.NCP1010ST100T3G.pdf
(24 pages)
Specifications of NCP1010ST100T3
Output Isolation
Isolated
Frequency Range
90 ~ 110kHz
Voltage - Input
8.5 ~ 10 V
Voltage - Output
700V
Power (watts)
19W
Operating Temperature
-40°C ~ 125°C
Package / Case
TO-261-4, TO-261AA, SOT-223-4
Duty Cycle (max)
72 %
Mounting Style
SMD/SMT
Switching Frequency
110 KHz
Operating Supply Voltage
- 0.3 V to + 10 V
Maximum Operating Temperature
+ 150 C
Synchronous Pin
No
Topology
Flyback
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
NCP1010ST100T3G
Manufacturer:
ON Semiconductor
Quantity:
3 300
370 Vdc. With ICC1 = 1.1 mA (65 kHz version), we can
expect a DSS dissipation around 407 mW. If you select a
higher switching frequency version, the ICC1 increases and
it is likely that the DSS consumption exceeds that number.
In that case, we recommend to add an auxiliary winding in
order to offer more dissipation room to the power MOSFET.
the Power Capability of the NCP101X Members” to help in
selecting the right part/configuration for your application.
Lowering the Standby Power with an Auxiliary Winding
dissipation is too high and extremely low standby power is
a must. In both cases, one can connect an auxiliary winding
to disable the self- -supply. The current source then ensures
the startup sequence only and stays in the off state as long as
V
that the insertion of a resistor (Rlimit) between the auxiliary
DC level and the V
internal 8.7 V active Zener diode during an overshoot for
instance (absolute maximum current is 15 mA) and to
implement the fail- -safe optocoupler protection as offered by
the active clamp. Please note that there cannot be bad
interaction between the clamping voltage of the internal
Zener and VCC
built on top of VCC
(200 mV typical).
applications often puzzles the designer. Actually, if a SMPS
operated at nominal load can deliver an auxiliary voltage of
an arbitrary 16 V (Vnom), this voltage can drop to below
10 V (Vstby) when entering standby. This is because the
recurrence of the switching pulses expands so much that the
low frequency refueling rate of the V
enough to keep a constant auxiliary voltage. Figure 19
portrays a typical scope shot of a SMPS entering deep
standby (output unloaded). So care must be taken when
calculating Rlimit 1) to not trigger the V
latch [by injecting 6.3 mA (min. value) into the active
clamp] in normal operation but 2) not to drop too much
voltage over Rlimit when entering standby. Otherwise the
DSS could reactivate and the standby performance would
degrade. We are thus able to bound Rlimit between two
equations:
Where:
Vnom is the auxiliary voltage at nominal load.
Vstdby is the auxiliary voltage when standby is entered.
< Vds(t) >= Vin
CC
Plugging Equations 7 and 8 into Equation 6 leads to
The worse case occurs at high line, when Vin equals
Please read application note AND8125/D, “Evaluating
The DSS operation can bother the designer when its
Self- -supplying controllers in extremely low standby
Vnom − Vclamp
does not drop below VCC
Itrip
OFF
and thus,
CC
since this clamping voltage is actually
≤ Rlimit ≤
OFF
pin is mandatory to not damage the
with a fixed amount of offset
P DSS = Vin × ICC1
ON
Vstby − VCC ON
or 7.5 V. Figure 18 shows
CC
ICC1
CC
capacitor is not
over current
(eq. 9)
(eq. 10)
http://onsemi.com
.
11
Itrip is the current corresponding to the nominal operation.
It must be selected to avoid false tripping in overshoot
conditions.
ICC1 is the controller consumption. This number slightly
decreases compared to ICC1 from the spec since the part in
standby almost does not switch.
VCC
to keep the DSS in the OFF mode. It is good to shoot around
8.0 V in order to offer an adequate design margin, e.g. to not
reactivate the startup source (which is not a problem in itself
if low standby power does not matter).
keep Vaux to around 8.0 V (as selected above), we purposely
select a Vnom well above this value. As explained before,
experience shows that a 40% decrease can be seen on
auxiliary windings from nominal operation down to standby
mode. Let’s select a nominal auxiliary winding of 20 V to
offer sufficient margin regarding 8.0 V when in standby
(Rlimit also drops voltage in standby). Plugging the
values in Equation 10 gives the limits within which Rlimit
shall be selected:
between auxiliary and power must be: 12/20 = 0.6. The OVP
latch will activate when the clamp current exceeds 6.3 mA.
This will occur when Vaux increases to: 8.7 V + 1.8 k x
(6.4m + 1.1m) = 22.2 V for the first boundary or 8.7 V +
3.6 k x (6.4m +1.1m) = 35.7 V for second boundary. On the
power output, it will respectively give 22.2 x 0.6 = 13.3 V
and 35.7 x 0.6 = 21.4 V. As one can see, tweaking the Rlimit
value will allow the selection of a given overvoltage output
level. Theoretically predicting the auxiliary drop from
nominal to standby is an almost impossible exercise since
many parameters are involved, including the converter time
constants. Fine tuning of Rlimit thus requires a few
iterations and experiments on a breadboard to check Vaux
variations but also output voltage excursion in fault. Once
properly adjusted, the fail- -safe protection will preclude any
lethal voltage runaways in case a problem would occur in the
feedback loop.
permanently disabled, the output voltage thus drops to zero.
The V
in this state until the user unplugs the power supply and
forces V
value, the internal OVP latch is reset and when the high
voltage is reapplied, a new startup sequence can take place
in an attempt to restart the converter.
Since Rlimit shall not bother the controller in standby, e.g.
If we design a power supply delivering 12 V, then the ratio
When an OVP occurs, all switching pulses are
ON
20 − 8.7
CC
6.3 m
is the level above which Vaux must be maintained
CC
cycles up and down between 8.5–4.7 V and stays
1.8 k < Rlimit < 3.6 k
to drop below 3.0 V (VCC
≤ Rlimit ≤ 12 − 8
1.1 m
, that is to say:
reset
). Below this
(eq. 11)