PKS606FN Power Integrations, PKS606FN Datasheet - Page 5
![IC OFFLINE SWIT OTP OCP HV TO262](/photos/7/32/73240/596-to-262-7c_sml.jpg)
PKS606FN
Manufacturer Part Number
PKS606FN
Description
IC OFFLINE SWIT OTP OCP HV TO262
Manufacturer
Power Integrations
Series
PeakSwitch®r
Specifications of PKS606FN
Mfg Application Notes
PeakSwitch Design Guide AppNote
Output Isolation
Isolated
Frequency Range
250 ~ 304kHz
Voltage - Output
700V
Power (watts)
117W
Operating Temperature
-40°C ~ 150°C
Package / Case
TO-262-7 (Formed Leads), 5 Leads
Output Voltage
12 V
Input / Supply Voltage (max)
265 VAC
Input / Supply Voltage (min)
85 VAC
Duty Cycle (max)
65 %
Switching Frequency
47 KHz
Supply Current
25 uA
Operating Temperature Range
- 40 C to + 150 C
Mounting Style
Through Hole
For Use With
596-1198 - KIT REF DESIGN 36-72W MOTOR DRVR
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
596-1125-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PKS606FN
Manufacturer:
power
Quantity:
15 000
Part Number:
PKS606FN
Manufacturer:
POWER
Quantity:
20 000
300
the line under-voltage sense circuit prevents a
restart attempt until the AC input voltage is removed
(I
the power MOSFET switching will resume once the AC input
voltage is applied again (I
a latching shutdown function with AC reset during such a fault
condition.
When a brownout or line sag occurs, output regulation may be
lost and the EN/UV pin will receive no feedback (it is pulled
low). A fter 30 ms of no feedback, MOSFET switching is disabled.
Since the AC line is abnormally low (I
switching remains disabled until normal line voltage is restored.
The power MOSFET switching will resume once the AC input
returns to normal (I
latching shutdown function during such a condition.
Auto-Restart (UV resistor not present)
In the event of a fault condition such as output overload,
output short circuit or an open loop condition, PeakSwitch
enters into auto-restart operation. An internal counter
clocked by the oscillator is reset every time the EN/UV pin
is pulled low. When the EN/UV pin receives no feedback
for 30 ms, the power MOSFET switching is disabled for
5 seconds (150 ms for the first auto-restart event). The
auto-restart alternately enables and disables the switching
of the power MOSFET until the fault condition is removed.
Figure 6 illustrates auto-restart circuit operation in the presence
of an output short circuit.
Adaptive Switching Cycle On-time Extension
Adaptive switching cycle on-time extension keeps the MOSFET
on until current limit is reached, instead of terminating after
the DC
because it only occurs after the ENABLE pin has been high
for approximately 750 µs, a condition that would arise if the
200
100
Figure 6. PeakSwitch Auto-Restart Operation.
10
0
5
0
EN
0
<25 µA). Then the internal auto-restart latch is reset and
MAX
signal goes low. This on-time extension is adaptive
V
DC-OUTPUT
V
DRAIN
EN
>25 µA). This effectively disables the
EN
>25 µA). This effectively provides
Time (s)
5
EN
<25 µA) MOSFET
10
Figure 8. PeakSwitch Operation at Moderately Heavy Loading.
peak output power was required in low line conditions. On-time
extension is disabled during the startup of the power supply.
PeakSwitch Operation
PeakSwitch devices operate in the current-limit mode. When
enabled, the oscillator turns the power MOSFET on at the
beginning of each cycle. The MOSFET is turned off when the
current ramps up to the current limit or when the DC
is reached. Since the highest current limit level and frequency
Figure 7. PeakSwitch Operation at Near Maximum Loading.
V
V
I
I
CLOCK
CLOCK
DRAIN
DRAIN
DRAIN
D
D
DRAIN
MAX
MAX
V
V
EN
EN
PKS603-607
PI-2667-090700
PI-2749-050301
MAX
Rev. I 02/07
limit
5