MXD1210CPA Maxim Integrated Products, MXD1210CPA Datasheet - Page 5
![IC CNTRLR NONVOLATILE RAM 8-DIP](/photos/1/39/13900/175-8-dip_sml.jpg)
MXD1210CPA
Manufacturer Part Number
MXD1210CPA
Description
IC CNTRLR NONVOLATILE RAM 8-DIP
Manufacturer
Maxim Integrated Products
Datasheet
1.MXD1210CSA.pdf
(9 pages)
Specifications of MXD1210CPA
Controller Type
Nonvolatile RAM
Voltage - Supply
4.75 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Package / Case
8-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MXD1210CPA
Manufacturer:
MAXIM
Quantity:
5 510
Company:
Part Number:
MXD1210CPA
Manufacturer:
PLESSEY
Quantity:
5 510
Part Number:
MXD1210CPA
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MXD1210CPA+
Manufacturer:
Maxim Integrated Products
Quantity:
135
The MXD1210 executes five main functions to perform
reliable RAM operation and battery backup (see the
Typical Operating Circuit and Figure 1):
1) RAM Power-Supply Switch: The switch directs
2) Power-Failure Detection: The write-protection
3) Write Protection: This holds the chip-enable out-
4) Battery Redundancy: A second battery is option-
power to the RAM from the incoming supply or
from the selected battery, whichever is at the
greater voltage. The switch control uses the same
criterion to direct power to MXD1210 internal cir-
cuitry.
function is enabled when a power failure is
detected. The power-failure detection range
depends on the state of the TOL pin as follows:
Power-failure detection is independent of the bat-
tery-backup function and precedes it sequentially
as the power-supply voltage drops during a typi-
cal power failure.
put (CEO) to within 0.2V of V
battery, whichever is greater. If the chip-enable
input (CE) is low (active) when power failure is
detected, then CEO is held low until CE is brought
high, at which time CEO is gated high for the
duration of the power failure. The preceding
sequence completes the current RD/WR cycle,
preventing data corruption if the RAM access is a
WR cycle.
al. When two batteries are connected, the
stronger battery is selected to provide RAM back-
up and to power the MXD1210. The battery-selec-
tion circuitry remains active while in the
battery-backup mode, selecting the stronger bat-
CONDITION
TOL = V
TOL = GND
CCO
_______________________________________________________________________________________
_______________________________________________________________________________________
Detailed Description
CCI
V
Main Functions
CCTP
4.75 to 4.50
4.50 to 4.25
or of the selected
RANGE (V)
Nonvolatile RAM Controller
First access: read memory location n, loc(n) = x
Second access: write memory location n,
Third access: read memory location n, loc(n) = ?
If the third access (read) is complement (x), then the
battery is good; otherwise the battery is not good.
Return to loc(n) = x following the test sequence.
The freshness-seal mode relates to battery longevity
during storage rather than directly to battery backup.
This mode is activated when the first battery is con-
nected, and is defeated when the voltage at V
exceeds V
teries are isolated from the system; that is, no current is
drained from either battery, and the RAM is not pow-
ered by either battery. This means that batteries can be
installed and the system can be held in inventory with-
out battery discharge. The positive edge rate at
VBATT1 and VBATT2 should exceed 0.1V/µs. The bat-
teries will maintain their full shelf life while installed in
the system.
The Typical Operating Circuit shows the MXD1210 con-
nected to write-protect the RAM when V
4.75V, and to provide battery backup to the supply.
5) Battery-Status Warning: This notifies the system
tery and isolating the weaker one. The battery-
selection activity is transparent to the user and
the system. If only one battery is connected, the
second battery input should be grounded.
when the stronger of the two batteries measures ≤
2.0V. Each time the MXD1210 is repowered (V
> V
tery voltage is measured. If the battery in use is
low, following the MXD1210 recovery period, the
device issues a warning to the system by inhibit-
ing the second memory cycle. The sequence is
as follows:
CCTP
CCTP
) after detecting a power failure, the bat-
loc(n) = complement (x)
. In the freshness-seal mode, both bat-
Freshness-Seal Mode
Battery Backup
CC
is less than
CCI
first
CCI
5
5