MD4811-D512-V3Q18-X-P/Y SanDisk, MD4811-D512-V3Q18-X-P/Y Datasheet - Page 27
MD4811-D512-V3Q18-X-P/Y
Manufacturer Part Number
MD4811-D512-V3Q18-X-P/Y
Description
IC MDOC G3 512MB 48-TSOP
Manufacturer
SanDisk
Datasheet
1.MD4331-D1G-V3Q18-X-PY.pdf
(97 pages)
Specifications of MD4811-D512-V3Q18-X-P/Y
Format - Memory
FLASH
Memory Type
FLASH - Nand
Memory Size
512M (64M x 8)
Speed
55ns
Interface
Parallel
Voltage - Supply
2.5 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
48-TSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
585-1136
- Current page: 27 of 97
- Download datasheet (2Mb)
AD[15:14]
AD[13:12]
AD[11:9]
AD[8:6]
AD[5:3]
AD[2:0]
CE#
OE#
WE#
AVD#
ID0
LOCK#
BUSY#
RSTIN#
CLK
DMARQ#
IRQ#
DPD
7x10 FBGA Package
24
Table 5: Signal Descriptions for Multiplexed Interface (Mobile DiskOnChip G3 7x10 FBGA Package)
Signal
K6, H5, H4
K4, J3, H3
K2, J7, G6
K3, G3, J2
Ball No.
H7, K7
H6, J6
G8
G7
G1
H1
H2
C5
E7
E4
D4
K5
F7
F8
Input
Type
OD
OD
OD
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
Preliminary Data Sheet, Rev. 1.1
Multiplexed bus. Address and data signals
Chip Enable, active low
Write Enable, active low
Output Enable, active low
Set multiplexed interface
Identification. Configuration control to support up to
two chips cascaded in the same memory window.
Chip 1 = ID0 = VSS; must be used for single-chip
Chip 2 = ID0 = VCC
Lock, active low. When active, provides full hardware
data protection of selected partitions.
Busy, active low, open drain. Indicates that
DiskOnChip is initializing and should not be accessed
A 10 KΩ pull-up resistor is required if this ball drives
an input. A 10 KΩ pull-up resistor is recommended
even if this ball is not used.
Reset, active low.
System Clock.
DMA Request, active low. A 10 KΩ pull-up resistor is
required if this ball drives an input. A 10 KΩ pull-up
resistor is recommended even if this ball is not used.
Interrupt Request, active low. A 10 KΩ pull-up resistor
is required if this ball drives an input. A 10 KΩ pull-up
resistor is recommended even if this ball is not used.
Deep Power-Down. Used to enter and exit Deep
Power-Down mode. Pin is assigned A0 instead of
DPD when working in 8-bit mode.
System Interface
Configuration
Control
configuration
Description
Mobile DiskOnChip G3
91-SR-011-05-8L
Input
Input
Input
Input
Input
Output
Output
Output
Input
Signal
Output
Input/
Type
Input
Input
Input
Related parts for MD4811-D512-V3Q18-X-P/Y
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC MDOC G3 512MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC G3 512MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC G3 512MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC G4 2GB 69-FBGA
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC P3 256MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC P3 256MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC P3 256MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC H1 8GB 115-FBGA
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC H3 1GB FBGA
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC H3 2GB FBGA
Manufacturer:
SanDisk
Datasheet: