M24C01-WMN6P STMicroelectronics, M24C01-WMN6P Datasheet - Page 9

• Manufacturer Part Number: M24C01-WMN6P
• Description: IC EEPROM 1KBIT 400KHZ 8SOIC
• Manufacturer: STMicroelectronics

Specifications of M24C01-WMN6P

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 1K (128 x 8)
• Speed: 400kHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Organization: 128 K x 8
• Interface Type: I2C
• Maximum Clock Frequency: 0.4 MHz
• Access Time: 900 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.5 V
• Maximum Operating Current: 2 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 2.5 V, 5.5 V
• Memory Configuration: 128 X 8
• Clock Frequency: 400kHz
• Supply Voltage Range: 2.5V To 5.5V
• Memory Case Style: SOIC
• No. Of Pins: 8
• Rohs Compliant: Yes
• Density: 1Kb
• Access Time (max): 900ns
• Frequency (max): 400KHz
• Write Protection: Yes
• Data Retention: 40Year
• Operating Supply Voltage (typ): 3.3/5V
• Package Type: SOIC
• Operating Temp Range: -40C to 85C
• Supply Current: 2mA
• Operating Supply Voltage (min): 2.5V
• Operating Supply Voltage (max): 5.5V
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-8558; M24C01-WMN6P

M24C16, M24C08, M24C04, M24C02, M24C01
2.4
2.4.1
2.4.2
2.4.3
2.4.4
Supply voltage (V
Operating supply voltage V
Prior to selecting the memory and issuing instructions to it, a valid and stable V
within the specified [V
Table
V
V
This voltage must remain stable and valid until the end of the transmission of the instruction
and, for a Write instruction, until the completion of the internal write cycle (t
Power-up conditions
The V
defined in
Device reset
In order to prevent inadvertent write operations during power-up, a power-on-reset (POR)
circuit is included. At power-up (continuous rise of V
instruction until V
than the minimum V
V
mode. The device, however, must not be accessed until V
voltage within the specified [V
In a similar way, during power-down (continuous decrease in V
below the power-on-reset threshold voltage, the device stops responding to any instruction
sent to it.
Power-down conditions
During power-down (continuous decrease in V
mode (mode reached after decoding a Stop condition, assuming that there is no internal
write cycle in progress).
CC
CC
CC
/V
line with a suitable capacitor (usually of the order of 10 nF to 100 nF) close to the
passes over the POR threshold, the device is reset and enters the Standby Power
8). In order to secure a stable DC supply voltage, it is recommended to decouple the
CC
SS
voltage has to rise continuously from 0 V up to the minimum V
package pins.
Table
6,
CC
Table 7
CC
reaches the power-on-reset threshold voltage (this threshold is lower
CC
operating voltage defined in
(min), V
CC
and
CC
)
Doc ID 5067 Rev 13
Table 8
CC
(min), V
CC
(max)] range must be applied (see
and the rise time must not vary faster than 1 V/µs.
CC
(max)] range.
CC
), the device must be in the Standby Power
CC
Table
), the device does not respond to any
CC
6,
Table 7
reaches a valid and stable V
CC
), as soon as V
and
Table
CC
Signal description
Table
operating voltage
W
6,
).
8). When
Table 7
CC
CC
voltage
drops
and
9/40
CC