MT48V8M16LFB4-10 IT:G Micron Technology Inc, MT48V8M16LFB4-10 IT:G Datasheet - Page 48
![IC SDRAM 128MBIT 100MHZ 54VFBGA](/photos/7/22/72286/557-54-fbga_sml.jpg)
MT48V8M16LFB4-10 IT:G
Manufacturer Part Number
MT48V8M16LFB4-10 IT:G
Description
IC SDRAM 128MBIT 100MHZ 54VFBGA
Manufacturer
Micron Technology Inc
Datasheet
1.MT48LC8M16LFB4-75MG_TR.pdf
(80 pages)
Specifications of MT48V8M16LFB4-10 IT:G
Format - Memory
RAM
Memory Type
Mobile SDRAM
Memory Size
128M (8Mx16)
Speed
100MHz
Interface
Parallel
Voltage - Supply
2.3 V ~ 2.7 V
Operating Temperature
-40°C ~ 85°C
Package / Case
54-VFBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
PDF: 09005aef807f4885/Source: 09005aef8071a76b
128Mbx16x32Mobile_2.fm - Rev. M 1/09 EN
10. For a READ without auto precharge interrupted by a READ (with or without auto pre-
11. For a READ without auto precharge interrupted by a WRITE (with or without auto pre-
12. For a WRITE without auto precharge interrupted by a READ (with or without auto pre-
13. For a WRITE without auto precharge interrupted by a WRITE (with or without auto pre-
14. For a READ with auto precharge interrupted by a READ (with or without auto precharge),
15. For a READ with auto precharge interrupted by a WRITE (with or without auto precharge),
16. For a WRITE with auto precharge interrupted by a READ (with or without auto precharge),
17. For a WRITE with auto precharge interrupted by a WRITE (with or without auto precharge),
6. All states and sequences not shown are illegal or reserved.
7. READs or WRITEs to bank m listed in the Command (Action) column include READs or
8. Concurrent auto precharge: Bank n will initiate the auto precharge command when its
9. Burst in bank n continues as initiated.
WRITEs with auto precharge enabled and READs or WRITEs with auto precharge disabled.
burst has been interrupted by bank m’s burst.
charge), the READ to bank m will interrupt the READ on bank n, CL later (see Figure 14 on
page 29).
charge), the WRITE to bank m will interrupt the READ on bank n when registered (see
Figure 16 and Figure 17 on page 31). DQM should be used one clock prior to the WRITE
command to prevent bus contention.
charge), the READ to bank m will interrupt the WRITE on bank n when registered (see
Figure 24 on page 37) with the data-out appearing CL later. The last valid WRITE to bank n
will be data-in registered 1 clock prior to the READ to bank m.
charge), the WRITE to bank will interrupt the WRITE on bank n when registered (see
Figure 22 on page 36). The last valid WRITE to bank n will be data-in registered 1 clock prior
to the READ to bank m.
the READ to bank m will interrupt the READ on bank n, CL later. The PRECHARGE to bank n
will begin when the READ to bank m is registered (see Figure 31 on page 42).
the WRITE to bank m will interrupt the READ on bank n when registered. DQM should be
used 2 clocks prior to the WRITE command to prevent bus contention. The PRECHARGE to
bank n will begin when the WRITE to bank m is registered (see Figure 32 on page 42).
the READ to bank m will interrupt the WRITE on bank n when registered, with the data-out
appearing CL later. The PRECHARGE to bank n will begin after
begins when the READ to bank m is registered. The last valid WRITE bank n will be data-in
registered 1 clock prior to the READ to bank m (see Figure 33 on page 43).
the WRITE to bank m will interrupt the WRITE on bank n when registered. The PRECHARGE
to bank n will begin after
istered. The last valid WRITE to bank n will be data registered 1 clock to the WRITE to bank
m (see Figure 34 on page 43).
t
WR is met, where
48
Micron Technology, Inc., reserves the right to change products or specifications without notice.
t
WR begins when the WRITE to bank m is reg-
128Mb: x16, x32 Mobile SDRAM
t
WR is met, where
©2001 Micron Technology, Inc. All rights reserved.
t
READs
WR