MT28F800B5WG-8 T TR Micron Technology Inc, MT28F800B5WG-8 T TR Datasheet - Page 4
![IC FLASH 8MBIT 80NS 48TSOP](/photos/7/22/72295/557-48-tsop_sml.jpg)
MT28F800B5WG-8 T TR
Manufacturer Part Number
MT28F800B5WG-8 T TR
Description
IC FLASH 8MBIT 80NS 48TSOP
Manufacturer
Micron Technology Inc
Datasheet
1.MT28F008B5VG-8_B.pdf
(30 pages)
Specifications of MT28F800B5WG-8 T TR
Format - Memory
FLASH
Memory Type
FLASH - Nor
Memory Size
8M (1M x 8 or 512K x 16)
Speed
80ns
Interface
Parallel
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Package / Case
48-TSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
PIN DESCRIPTIONS
09005aef8075d1ec
MT28F800B5_4.fm - Rev. 4, Pub. 2/2004
44-PIN SOP
11, 10, 9, 8,
NUMBERS
42, 41, 40,
39, 38, 37,
36, 35, 34,
15, 17, 19,
21, 24, 26,
16, 18, 20,
22, 25, 27,
7, 6, 5, 4,
28, 30
13, 32
3, 2
43
12
44
14
33
31
29
23
1
–
–
25-28, 32-35
15, 14, 8, 7,
NUMBERS
21, 20, 19,
18, 17, 16,
36, 6, 5, 4,
3, 2, 1, 40,
40-PIN
13, 37
30, 31
23, 39
29, 38
TSOP
12
22
10
24
11
9
–
–
–
8, 7, 6, 5, 4,
NUMBERS
20, 19, 18,
3, 2, 1, 48,
29, 31, 33,
35, 38, 40,
30, 32, 34,
36, 39, 41,
23,22, 21,
9, 10, 15
48-PIN
25, 24,
17, 16
42, 44
27, 46
TSOP
11
14
26
12
28
47
45
43
13
37
DQ0–DQ7
SYMBOL
A0–A18/
BYTE#
DQ15/
DQ8–
DQ14
(A19)
(A-1)
WE#
WP#
OE#
CE#
RP#
V
V
V
NC
PP
CC
SS
SMART 5 BOOT BLOCK FLASH MEMORY
Output
Output
Output
Supply
Supply
Supply
Input/
Input/
Input/
TYPE
Input
Input
Input
Input
Input
Input
Input
–
4
Write Enable: Determines if a given cycle is a WRITE cycle.
If WE# is LOW, the cycle is either a WRITE to the command
execution logic (CEL) or to the memory array.
Write Protect: Unlocks the boot block when HIGH if V
V
not affect WRITE or ERASE operation on other blocks.
Chip Enable: Activates the device when LOW. When CE# is
HIGH, the device is disabled and goes into standby power
mode.
Reset/Power-Down: When LOW, RP# clears the status
register, sets the internal state machine (ISM) to the array
read mode and places the device in deep power-down
mode. All inputs, including CE#, are “Don’t Care,” and all
outputs are High-Z. RP# unlocks the boot block and
overrides the condition of WP# when at V
held at V
Output Enable: Enables data output buffers when LOW.
When OE# is HIGH, the output buffers are disabled.
Byte Enable: If BYTE# = HIGH, the upper byte is active
through DQ8–DQ15. If BYTE# = LOW, DQ8–DQ14 are High-
Z, and all data is accessed through DQ0–DQ7. DQ15/(A - 1)
becomes the least significant address input.
Address Inputs: Select a unique 16-bit word or 8-bit byte.
The DQ15/(A - 1) input becomes the lowest order address
when BYTE# = LOW (MT28F800B5) to allow for a selection
of an 8-bit byte from the 1,048,576 available.
Data I/O: MSB of data when BYTE# = HIGH.
during READ or WRITE operation.
Data I/Os: Data output pins during any READ operation or
data input pins during a WRITE. These pins are used to
input commands to the CEL.
Data I/Os: Data output pins during any READ operation or
data input pins during a WRITE when BYTE# = HIGH. These
pins are High-Z when BYTE# is LOW.
Write/Erase Supply Voltage: From a WRITE or ERASE
CONFIRM until completion of the WRITE or ERASE, VPP
must be at 5V. VPP = “Don’t Care” during all other
operations.
Power Supply: +5V ±10%.
Ground.
No Connect: These pins may be driven or left unconnected.
Address Input: LSB of address input when BYTE# = LOW
PPH
(5V) and RP# = V
Micron Technology, Inc., reserves the right to change products or specifications without notice.
IH
during all other modes of operation.
IH
DESCRIPTION
during a WRITE or ERASE. Does
HH
©2002 Micron Technology Inc.
; RP# must be
8Mb
PP
=