AT29LV512-15TU Atmel, AT29LV512-15TU Datasheet
AT29LV512-15TU
Specifications of AT29LV512-15TU
Available stocks
Related parts for AT29LV512-15TU
AT29LV512-15TU Summary of contents
Page 1
... Three-volt-only commands determine the opera- tion of the device. Reading data out of the device is similar to reading from an EPROM. Reprogramming the AT29LV512 is performed on a sector basis; 128 bytes of data are loaded into the device and then simultaneously programmed. ...
Page 2
... Pin Configurations Pin Name A0 - A15 I/O0 - I/O7 NC 2.1 32-lead PLCC Top View 2.2 32-lead TSOP (Type 1) Top View AT29LV512 2 Function Addresses Chip Enable Output Enable Write Enable Data Inputs/Outputs No Connect A14 A13 A11 A10 I/ I/O7 A11 A13 4 A14 VCC A15 11 A12 ...
Page 3
... Device Operation 4.1 Read The AT29LV512 is accessed like an EPROM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state whenever high. This dual- line control gives designers flexibility in preventing bus contention ...
Page 4
... DATA Polling The AT29LV512 features DATA polling to indicate the end of a program cycle. During a program cycle an attempted read of the last byte loaded will result in the complement of the loaded data on I/O7. Once the program cycle has been completed, true data is valid on all outputs and the next cycle may begin ...
Page 5
... Toggle Bit In addition to DATA polling, the AT29LV512 provides another method for determining the end of a program or erase cycle. During a program or erase operation, successive attempts to read data from the device will result in I/O6 toggling between one and zero. Once the program cycle has completed, I/O6 will stop toggling and valid data will be read ...
Page 6
... A15 = A15 = V Condition MHz mA 3.6V OUT 1 -100 µ 3. AT29LV512-12 -40°C - 85°C 3.3V 0. OUT High Z High Z ( Manufacturer Code ( Device Code Manufacturer Code Device Code IH Min Max 0.6 2.0 0.45 2.4 0177O–FLASH–9/08 (4) (4) (4) (4) Units µ ...
Page 7
... This parameter is characterized and is not 100% tested. 11. Input Test Waveforms and Measurement Level 12. Output Test Load 0177O–FLASH–9/08 (1)(2)(3)( after the address transition without impact on t ACC after the falling edge of CE without impact < AT29LV512 AT29LV512-12 Min Max Units 120 ns 120 ACC ...
Page 8
... Chip Select Hold Time CH t Write Pulse Width ( Data Set-up Time Data, OE Hold Time DH OEH t Write Pulse Width High WPH 15. AC Byte Load Waveforms 15.1 WE Controlled 15.2 CE Controlled AT29LV512 8 Max Units 6 12 (1)(2) Conditions OUT Min Max Units 0 ns 100 ...
Page 9
... LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA A0 TO ADDRESS 5555 WRITES ENABLED LOAD DATA TO ENTER DATA (3) (2) SECTOR (128 BYTES) PROTECT STATE AT29LV512 Min Max Units 100 ns 100 200 ns 150 µs 200 ns ...
Page 10
... AC Read Characteristics. OE 22. Toggle Bit Waveforms Notes: 1. Toggling either both OE and CE will operate toggle bit. 2. Beginning and ending state of I/O6 will vary. 3. Any address location may be used but the address should not vary. AT29LV512 10 (1) (1) (1)(3) Min Typ Max ...
Page 11
... ADDRESS 2AAA LOAD DATA 90 TO ADDRESS 5555 PAUSE 20 mS ENTER PRODUCT IDENTIFICATION (2)(3)(5) MODE ; Device Code is read for (1) LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA F0 TO ADDRESS 5555 PAUSE 20 mS EXIT PRODUCT IDENTIFICATION (4) MODE AT29LV512 . IH 11 ...
Page 12
... Green Package Option (Pb/Halide-free) I (mA ACC (ns) Active Standby 120 15 0.05 32J 32-lead, Plastic J-leaded Chip Carrier (PLCC) 32T 32-lead, Thin Small Outline Package (TSOP) AT29LV512 12 Ordering Code Package AT29LV512-12JU 32J AT29LV512-12TU 32T Package Type Operation Range Industrial (-40to 85C) 0177O–FLASH–9/08 ...
Page 13
... Lead coplanarity is 0.004 (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0177O–FLASH–9/08 1.14(0.045 PIN NO. 1 IDENTIFIER TITLE 32J, 32-lead, Plastic J-leaded Chip Carrier (PLCC) AT29LV512 0.318(0.0125) 0.191(0.0075 COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX SYMBOL A 3.175 – ...
Page 14
... E Notes: 1. This package conforms to JEDEC reference MO-142, Variation BD. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT29LV512 14 PIN SEATING PLANE A1 TITLE ...
Page 15
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...